How to tune your philips TV 20 channels

Does the TV support digital TV

If the box from the device has been preserved, then it should contain a brief specification indicating support for the DVB-T2 format. Similar information can be found in the operating instructions. If there is no documentation, then it is worth inspecting the rear panel of the TV. An interface labeled DigitalInput indicates that the model supports digital TV.

Important! Devices manufactured before 1998 do not work with DVB-T2 format. Until 2004, equipment was only partially equipped with digital outputs: these were expensive TVs with a diagonal of more than 40 inches. The format began to be introduced everywhere after 2005.

You can also visit the brand’s website. After entering the TV model in the search box, a page with a detailed description of the device will open, where all the characteristics are indicated, including support for DVB-T2. As an alternative to the official resource, you can use the same Yandex Market or any other large trading platforms. If the TV does not support digital broadcasting, then you will have to buy a special set-top box.

tune, philips, channels

How to tune your Philips TV to cable TV

To set up cable TV programs on Philips television equipment, you must proceed in the following sequence:

  • Press the Home key on the remote control and enter the Menu.
  • Find the Configuration section.
  • Select Settings and then Channel Setup.
  • Set Automatic mode.
  • Launch Click.
  • Reinstall with the country name. This is usually Finland or Norway. Such a choice is necessary to activate cable television (in the Russian Federation, such activation is officially impossible).
  • Then you should indicate Cable, Settings and set the manual transmission speed mode and the indicator 7000.
  • Perform Fast or Full Scans. Analogue channels must be turned on, otherwise only digital channels will be tuned.
  • Upon completion of the search, click Finish.

You can now watch TV on cable TV.

Set up digital channels on your Philips TV

Modern TVs need preliminary setup: network connection, channel search. In general, the procedure is intuitive: you just have to trust the system prompts. However, some users still have difficulties. Below we give a detailed manual for Philips TVs.

Manual Channel Tuning

If there are any problems with the automatic search, then the scan can be performed in manual mode. You can find out the specific data of digital TV broadcasting using the RTRS online service. It is enough to indicate the nearest tower.

  • Open the TV menu and go to the settings.
  • Click on the “Installation” section.
  • We go to the “Channel search”
  • Selecting “Manual Mode”.
  • Enter data from the RTRS website.
  • Start scanning.
  • When finished, save the channel list.

The search can be noticeably delayed if the tower is located at a considerable distance from the antenna. When there is heavy rain outside the window, thunderstorm and other bad weather, it is better to postpone the scan to another more fine day.

If all manipulations were performed without errors, the smart product starts showing all stored digital channels that are available in your area. If you have problems with the show, you should find out why the TV does not catch channels.

That’s all the difficulty of how to tune digital channels on a Philips TV when it has the features of a modern Smart TV. Perhaps the following will help many users when making such settings.

How to reset settings

There are times when the TV is blocked by some negligence. In this case, you need to know how to return the equipment to working condition. Philips TVs have this option.

Signs indicating a blocked TV screen:

  • there is no sound and image, a key is visible on the screen, the TV does not respond to key presses;
  • you are prompted to enter a password to activate the TV;
  • only one channel turns on, the rest do not work.

The problem with blocking the TV can be solved by knowing the combination of numbers on the control panel, the input of which will help to instantly start the equipment. For password options, refer to the instruction manual for your Philips TV model.

Some actions to take when a blocking problem occurs:

  • See the combination in the TV user manual.
  • Try to restart channel scan, maybe their settings are lost.
  • The old version of the TV firmware may not work correctly. In this case, you will have to reflash. For this, specialists are involved in this matter.

In order not to search and remember the TV unlock pin code and reset all settings to factory settings, the developers have set the simplest combinations of numbers: 0000, 1111, 1234. Due to the simplicity of the codes, some subscribers decide to change the code and come up with a complex order of numbers. If the user has lost and forgot the code, then you need to do the following:

  • Go to the Settings menu, select the Security item and click Reset Code.
  • Then they enter the wrong order of the numbers, but do not confirm it.
  • Press the buttons to navigate through the channels on the remote control in the following sequence: 2 times up, down, up.
  • Enter code 0313 and click OK.

The password will be set to the initial one. To unblock the TV, use the Parental Control option to turn on the TV using the standard code.

Advice. Some TVs can unlock with one press of the DISP key. It only needs to be held down for 10.15 seconds.

For digital broadcasting

This type of signal transmission has huge advantages over the analog method. First, the quality of the image increases significantly. Secondly, now it is possible to broadcast a picture of the highest resolution, and thirdly, the absence of any interference. The net is able to withstand wet weather, strong gusts of wind, adhesion of snow and icing. All of these benefits can only be experienced with a modern TV, such as a Philips LCD. How to tune your Philips TV to receive digital TV channels?

In order to set up the broadcast, you need to press the Home button to enter the TV Menu. Next, perform the following steps:

  • In the Configuration section, find the Installation and Tuning of Channels. Once in this service, you can tune digital and analog channels.
  • Depending on the user’s wishes, the following actions are performed:
  • reinstallation. consists in completely removing already installed channels and scanning again, while digital and then analog channels will be in the first rows;
  • update. the channels are tuned over the old ones, but without deleting, but with adding new ones. The found channels will be placed at the end of the ruler.
  • A country is selected from the list with the presence of an official cable TV, the Cable item is set, the search parameters are indicated.
  • Search starts.
READ  How To Connect Channels Via Smart TV

Philips TVs do not have the ability to tune Tricolor TV automatically. Fine tuning can only be done manually.

  • Before starting auto search, you need to set the language and location.
  • In the window that appears, indicate the installation of the satellite channel.
  • In models in which two built-in tuners are installed, you need to select the one tuner item in the Menu and turn on the search.
  • Next, go to manual settings. As a result, the scale of the incoming signal should appear on the screen.
  • Click Install.
  • Selected channel Russia NTV
  • Start quick search.
  • When finished, press Stop.

Not every model has an automatic search

Automatic search does not work on all Philips TV models, which significantly increases the scan time. Manual setting of Tricolor TV looks like this:

  • Using the remote control, the Settings window opens.
  • Specify Satellite installation and select the Manual option.
  • It is necessary to mark the satellite Eutelsat W4 36E, set circular left polarization and automatic speed.
  • The search for a satellite is started in each individual frequency.
  • The found channels are saved.

Automatic tuning

  • Find the Home button on the remote control. By clicking on it, go to the Configuration section and select Channel Search.
  • Marks Reinstallation and write the country in the window that appears. It is necessary to indicate the name of the country in which cable TV operates officially (Finland, Germany, France). According to the official version, there is no cable television in the CIS countries.
  • Switching to Cable TV DVB-C.
  • The next step is to start scanning. To do this, click the Settings tab on the screen.
  • You will be prompted to select the type of search (auto or manual). Selectable Automatic.
  • In order for scanning to detect not only digital, but also analogue channels, select the On checkbox in the Analogue menu.
  • After confirming all the settings, click Ready and after 10 minutes everything will be finished.

How to tune your Philips TV to cable TV

To set up cable TV programs on Philips television equipment, you must proceed in the following sequence:

  • On the remote control, press the Home key and enter the Menu.
  • Find the Configuration section.
  • Select Settings and then Channel Setup.
  • Set Automatic mode.
  • Launch Click.
  • Reinstall with the country name. This is usually Finland or Norway. Such a choice is necessary to activate cable television (in the Russian Federation, such activation is officially impossible).
  • Then you should indicate Cable, Settings and set the manual transmission speed mode and the indicator 7000.
  • Perform Fast or Full Scans. Analogue channels must be turned on, otherwise only digital channels will be tuned.
  • Upon completion of the search, click Finish.

You can now watch TV on cable TV.

Set up channels on your Philips TV

Modern television equipment is undergoing incredible changes from year to year. It has become a reality to connect TVs to computers, cam-modules, tuners, game consoles, wired and wireless Internet. Philips is not the last among the leaders in the production of electrical equipment and produces devices and many other useful and necessary equipment with a wide range of functionality. You can understand the Philips TV settings on your own, the main thing is to adhere to the recommendations for adjusting this equipment.

For digital broadcasting

This type of signal transmission has huge advantages over the analog method. First, the quality of the image increases significantly. Secondly, now it is possible to broadcast a picture of the highest resolution, and thirdly, the absence of any interference. The net is able to withstand wet weather, strong gusts of wind, adhesion of snow and icing. All of these benefits can only be experienced with a modern TV, such as a Philips LCD. How to tune your Philips TV to receive digital TV channels?

In order to set up the broadcast, you need to press the Home button to enter the TV Menu. Next, perform the following steps:

  • In the Configuration section, find the Installation and Tuning of Channels. Once in this service, you can tune digital and analog channels.
  • Depending on the user’s wishes, the following actions are performed:
  • reinstallation. consists in completely removing already installed channels and scanning again, while digital and then analog channels will be in the first rows;
  • update. the channels are tuned over the old ones, but without deleting, but with adding new ones. The found channels will be placed at the end of the ruler.
  • A country is selected from the list with the presence of an official cable TV, the Cable item is set, the search parameters are indicated.
  • Search starts.

How to set up your Philips TV

If we take models of two different generations, then they may differ in interface, but the principle of adjustment will remain the same. A feature of the setting is the appearance of pop-up prompts on the screen with a request to enter a specific password for further actions. These are standard requirements and the combination of numbers in this case consists of 0000, 1111, 1234.

Follow the steps in the instructions to set up your Philips TV

To set up modern Philips TV equipment, you need to perform a quick or full scan. In the first case, the frequency difference is set, the analog signal is turned off (if the setting was previously carried out) and the Search is connected. In the case of a full scan, the Manual mode is set, the frequency is 298 and the QAM at 256, the analog signal is turned on or off, if it is already configured, the search is started. With correct setup, the screen should display free channels broadcast in the region.

The models released before 2011 have their own nuances associated not only with the appearance, but also with the presence of the interface. The algorithm for tuning satellite channels on the TV is as follows:

  • start automatic mode;
  • after the end of the procedure, you should confirm the search result.

In this video, you will learn more about channel setup:

Channels

How to set up channels is detailed in the user manual that is included in the package. If the TV was bought for any reason without it, then the setup manual can be found on the Internet at the official website of the equipment manufacturer. Philips remote control required for effective search.

  • Through the Menu on the remote control enter the list and select Configuration.
  • It is necessary to point to the item Installation.
  • Include Search in Silent Installation.
  • Next, you need to proceed with the Reinstallation of channels indicating the country with digital broadcasting.
  • In the Cable section, the baud rate is set, as well as the type of scan (fast or full).
  • Includes analogue channels to search and starts Get Started.
  • When finished, you need to exit the settings by clicking on Finish.

Menu is selected on the TV remote control. If the TV equipment is still completely new and has not been switched on (there is no stored channel data), the TV screen will display a Menu similar to Setup. The language prompt should appear automatically. The required language is selected from the list and confirmed by the OK button on the remote control.

READ  Half Of The TV Screen Is Darker What To Do

Next, you must specify the country in which the equipment is located. From the proposed list, by moving the cursor, the name of the country is selected.

To debug the sound quality on your Philips TV, there are a few steps to follow:

  • In the Menu, you need to find the house icon and the inscription Sound or Sound. Navigating the Settings window is performed using the remote control, moving the cursor up and down, right and left.
  • If the sound is not quite clear, you can apply manual adjustment of the bass and treble.
  • If there is no sound from the TV speakers, pay attention to the EasyLink tab in the Speakers section. It needs to be activated.
  • You can change the sound parameters by adjusting the volume level and the stereo sound balance. There is also a surround sound function.

It’s easy to set up sound on a TV like this

Tricolor

Philips TVs do not have the ability to tune Tricolor TV automatically. Fine tuning can only be done manually.

Advice. Before you start searching for channels, it is best to start scanning the Tricolor satellite. If it is detected by the antenna, the channel should not be saved.

  • Before starting auto search, you need to set the language and location.
  • In the window that appears, indicate the installation of the satellite channel.
  • In models in which two built-in tuners are installed, you need to select the one tuner item in the Menu and turn on the search.
  • Next, go to manual settings. As a result, the scale of the incoming signal should appear on the screen.
  • Click Install.
  • Selected channel Russia NTV
  • Start quick search.
  • When finished, press Stop.

Not every model has an automatic search

Automatic search does not work on all Philips TV models, which significantly increases the scan time. Manual setting of Tricolor TV looks like this:

  • Using the remote control, the Settings window opens.
  • Specify Satellite installation and select the Manual option.
  • It is necessary to mark the satellite Eutelsat W4 36E, set circular left polarization and automatic speed.
  • The search for a satellite is started in each individual frequency.
  • The found channels are saved.

How to reset settings

There are times when the TV is blocked by some negligence. In this case, you need to know how to return the equipment to working condition. Philips TVs have this option.

Signs indicating a blocked TV screen:

  • there is no sound and image, a key is visible on the screen, the TV does not respond to key presses;
  • you are prompted to enter a password to activate the TV;
  • only one channel turns on, the rest do not work.

The problem with blocking the TV can be solved by knowing the combination of numbers on the control panel, the input of which will help to instantly start the equipment. For password options, refer to the instruction manual for your Philips TV model.

Some actions to take when a blocking problem occurs:

  • See the combination in the TV user manual.
  • Try to restart channel scan, maybe their settings are lost.
  • The old version of the TV firmware may not work correctly. In this case, you will have to reflash. For this, specialists are involved in this matter.

In order not to search and remember the TV unlock pin code and reset all settings to factory settings, the developers have set the simplest combinations of numbers: 0000, 1111, 1234. Due to the simplicity of the codes, some subscribers decide to change the code and come up with a complex order of numbers. If the user has lost and forgot the code, then you need to do the following:

  • Go to the Settings menu, select the Security item and click Reset Code.
  • Then they enter the wrong order of the numbers, but do not confirm it.
  • Press the buttons to navigate through the channels on the remote control in the following sequence: 2 times up, down, up.
  • Enter code 0313 and click OK.

The password will be set to the initial one. To unblock the TV, use the Parental Control option to turn on the TV using the standard code.

Advice. Some TVs can unlock with one press of the DISP key. It only needs to be held down for 10.15 seconds.

Philips TV remote control

The remote control for Philips TV is conventionally divided into three zones, each of which includes a certain set of buttons.

Upper part of the console:
1) On button. turning the TV on and off
2) Play buttons. play, stop, pause, rewind.
3) TV GUIDE button. electronic gear guide.
SETUP button. opening the setup page.
FORMAT button. picture format menu
Middle part of the remote control:
1) SOURCES button. menu of the list of connected devices.
2) Color buttons. Direct selection of parameters. The blue button opens the help.
3) INFO button. Information about programs.
4) BACK button. Return to the previously selected channel.

5) HOME button. Main menu.
6) EXIT button. switch to watching TV channels.
7) OPTIONS button. Entering or exiting the Options menu.
8) OK button. Setpoint confirmation.
9) Navigation buttons. Move up, down, left and right.
10) LIST button. Opening or Closing the Channel List.

Bottom of the remote control:
1) /. buttons. Volume control.
2) Number and letter buttons. Select TV channel directly or enter text.
3) SUBTITLE button. Enabling subtitles.
4) CHANNEL button. Switch channels, go to the next teletext page.
5) Button Mute. Instant mute
6) TEXT button. Display
teletext functions
On our website you can download the TV Remote
location and designation of remote control buttons, as well as instructions and user manual

Manual for TV PHILIPS

TV manual Philips recommends using a high speed HDMI connection to connect external devices. HDMI cable transfers both sound and image at the same time.
If external devices are connected via HDMI ports and support EasyLink technology, they can be controlled by the OEM TV remote control by enabling the EasyLink CEC function on all devices. By default, this feature is enabled on the TV. Depending on the manufacturer, the names of the HDMI CEC function differ and can be called Anynet from Samsung, Aquos Link from Sharp, Bravia Theater Sync from Sony, Kuro Link from Pioneer, Simplink from LG, Viera Link from Panasonic. Not all devices from other brands are fully EasyLink compatible.

If the external device has only a DVI connector, according to the instructions for the TV, use a DVI adapter to connect. HDMI.
The Philips 40PFT4109 / 60 TV is designed to connect a soundbar or home theater to the HDMI 1 port. This port supports the HDMI ARC function, which eliminates the need for additional audio cables, since HDMI ARC technology allows you to transfer both video and sound.
Philips TV is connected to the connectors located on the back and on the side of the TV.

On the back of your Philips TV you will find the following connectors:
HDMI high speed connection. HDMI1 ARC has an audio return channel.
SERV service port.
TV ANTENNA: 75 Om coaxial IEC
SCART (RGB / CVBS) connection of external devices.

The side of your Philips TV contains:
Digital Audio OUT: SPDIF high quality audio output
CI slot common interface
USB connectors for connecting USB devices
Satellit satellite dish connection

How to tune channels on your TV

How do I tune channels on my philips TV in a convenient TV program sequence? This is not always easy, since many TV models do not have the ability to sort channels after auto-tuning. The developers have provided for the creation of a folder of favorite channels, in which you can enter the necessary TV programs in the desired sequence, but this is often inconvenient for the user. You can tune the TV to the channels in a convenient sequence by starting the automatic tuning of television channels, and further setting the set of your favorite TV programs to the first places in the manual tuning mode.

READ  How to connect a microphone to a TV for karaoke

How to set up a Philips TV

Our masters configure Philips TVs with all the necessary settings.
Experienced specialists will tune the channels of television programs and arrange them in a convenient sequence, configure the settings for connecting the TV to a home computer network and Internet access, optimize individual user settings.
We know how to tune channels on a Philips TV! 8 (926).444-16-66 Master call.-
For your convenience, a Consultation on setting up TVs is organized.

Tuning TV channels

Any channels on your Philips TV in the ALL FAVORITE RADIO NEW can be renamed. To do this, select the channel you want to rename in the list, press the OPTIONS button on the remote control, select the RENAME item and then press OK. The new name can be entered directly from the keyboard of the remote control or using the on-screen keyboard.

Set up digital channels on your Philips TV

Modern TVs need preliminary setup: network connection, channel search. In general, the procedure is intuitive: you just have to trust the system prompts. However, some users still have difficulties. Below we give a detailed manual for Philips TVs.

Automatic channel search

After connecting the antenna, you need to scan the channels. Some models carry out this procedure automatically, while others require manual adjustment. The exact steps depend on the year the TV was manufactured.

  • We go into the settings by pressing the Home key.
  • Open the section “Configuration”.
  • Go to the “Installation” tab and agree with the OS warning about the consequences of the changes.
  • Click on “Channel settings”. “Automatic”. “Launch”.
  • Some firmwares offer to select a country. If Russia is not on the list, then we stop at Switzerland, Finland or Germany.
  • We put a tick on the item “Digital” in the “Setting Mode”.
  • Select “TV-antenna” as a signal source.
  • Press “Autosearch” and wait for the end of the procedure.
  • We save the found channels by clicking on “Finish”.

Important! At one stage, the operating system may require you to enter a password. If it has not changed before, then the options should be suitable: 0000, 1234 or 1111.

  • We go to the main menu by pressing the Home key.
  • Click on the “Installation” section.
  • Open the submenu “Search for channels”.
  • In the next window, select “Reinstall Channels”.
  • In the drop-down list of countries, click on Russia (Germany, Finland, Sweden).
  • Set the search mode. digital.
  • Signal source. antenna.
  • Click on “Frequency scan”. “Fast”. “Launch”.
  • We are waiting for the end of the procedure and save the changes.

SmartTV network settings

For technology of the SmartTV format, manual adjustment of the network may additionally be required. This is primarily necessary to receive firmware updates, which will allow you to get the most out of your TV.

  • We connect the cable to the TV or activate the wireless router.
  • In the settings, select “Connect to the network”.
  • Click on the desired line: cable or Wi-Fi.
  • In the case of a router, we launch a scan and, if necessary, enter a password.
  • If the firmware version is not up to date, then when the connection is established, the OS will offer to update it.

After the end of the procedure, you can start scanning the channels. On Smart-TV, just open the “Channel settings” item and press the “Search” button. The OS will do the rest.

Does the TV support digital TV

If the box from the device has been preserved, then it should contain a brief specification indicating support for the DVB-T2 format. Similar information can be found in the operating instructions. If there is no documentation, then it is worth inspecting the rear panel of the TV. An interface labeled DigitalInput indicates that the model supports digital TV.

Important! Devices manufactured before 1998 do not work with DVB-T2 format. Until 2004, equipment was only partially equipped with digital outputs: these were expensive TVs with a diagonal of more than 40 inches. The format began to be introduced everywhere after 2005.

You can also visit the brand’s website. After entering the TV model in the search box, a page with a detailed description of the device will open, where all the characteristics are indicated, including support for DVB-T2. As an alternative to the official resource, you can use the same Yandex Market or any other large trading platforms. If the TV does not support digital broadcasting, then you will have to buy a special set-top box.

Initial setup

In the same way, we indicate the country. Russia. Otherwise, some of the functionality may not work correctly. It will be useful to indicate the time zone and set the correct time, if the system did not do it automatically: it will be useful when activating the timer and other features tied to time intervals.

Antenna connection

The antenna must be connected when the power is off, otherwise the control unit can be overloaded. It is important not to confuse the terrestrial input (RF-IN) with the satellite (SatelliteIN). The latter comes with a thread, and its inner part is filled with plastic with a small hole in the middle.

The etheric entrance is slightly larger in diameter and hollow inside. The plug should be inserted with little force and should not go around the connector. Poor contact is noise, artifacts and other image problems. Sometimes the connector is labeled ANT.

Manual Channel Tuning

If there are any problems with the automatic search, then the scan can be performed in manual mode. You can find out the specific data of digital TV broadcasting using the RTRS online service. It is enough to indicate the nearest tower.

  • Open the TV menu and go to the settings.
  • Click on the “Installation” section.
  • We go to the “Channel search”
  • Selecting “Manual Mode”.
  • Enter data from the RTRS website.
  • Start scanning.
  • When finished, save the channel list.

The search can be noticeably delayed if the tower is located at a considerable distance from the antenna. When there is heavy rain outside the window, thunderstorm and other bad weather, it is better to postpone the scan to another more fine day.

If all manipulations were performed without errors, the smart product starts showing all stored digital channels that are available in your area. If you have problems with the show, you should find out why the TV does not catch channels.

That’s all the difficulty of how to tune digital channels on a Philips TV when it has the features of a modern Smart TV. Perhaps the following will help many users when making such settings.