How To Tune A Dexp TV Without Antenna

Checking DVB-T2 on DEXP TV

Before starting all work, you need to make sure that your Dexp model is adapted to receive digital television. To do this, the TV must work with the broadcast standard. DVB-T2.

You can check the availability of the possibility of accepting a digit in several ways:

    Enter your TV model on our website. To do this, select “TVs” in the equipment menu. The table will show many companies, you just need to enter the number of your device. If the search finds it, then you can safely proceed to the next section of the setup.

If you could not decide in the above ways, then you can ask a question in the comments, we will try to help you with your searches. If it turns out that the TV cannot work with the DVB-T2 standard, you will additionally need to purchase a digital set-top box.

Tuning digital channels on all DEXP TVs

After you have made sure that your device can receive digital. We can move on to direct practice and set up digital channels using a real example. The instruction will be given using the example of the first DEXP TV model that came to our eyes. However, it will be SIMilar for the rest.

  • First of all, you need to connect the TV to the antenna. To do this, find the corresponding input on the back of the TV. RSA, indicated in the screenshot, will be needed if we need to additionally connect a set-top box. If the TV catches the digit on its own, we only need an antenna.
  • After that, press the “Source” button from the TV remote control. A special table should appear. In it, you need to select the mode in which the work on channel tuning will take place. In our case, this is DTV (Digital Television). To select, press OK or Enter. This should be done without delay. On some DEXP models, the settings windows remain active for a few seconds and then disappear. In this case, you have to configure everything again.
  • Press the “MENU” button on the remote control and use the up / down arrows to find the section: “Channels”. Next, we will look at setting up and searching directly, in automatic and manual mode. Depending on the situation, you may need any of them.
  • The first step is to autosearch. In most cases, it is sufficient to find all 20 digital channels. To do this, select the appropriate menu item from the remote control and press Enter. In the window that appears, we are only interested in digital channels, so we select only them.
  • The autosearch procedure will last for 5-10 minutes. During this time, the TV will search all available frequency ranges. In this case, the screen will display the number of found channels and radio stations. Depending on the year of manufacture of the DEXP model, the setting can be made according to DVB-T and DVB-T2 standards.

Instructions for connecting and setting up digital channels on Dexp TVs

According to our modest statistics, Dexp digital TVs are among the top 10 devices for which subscribers have questions. The reason here is, first of all, that there are no normal step-by-step instructions showing the general process of connecting and setting up digital channels. Looking ahead, let’s say that in terms of quality, these TVs are in demand. In addition, they are still bought for a relatively low price by our standards. For example, for a screen of 50 cm, you will be asked no more than 7,000 rubles, which, in principle, is very good.

Today we will thoroughly study the procedure for searching for channels on the devices of this company. In addition, we will analyze the process for the complete setting for a figure using a real example. In parallel with this, we will study the main purpose of certain buttons on the TV, as well as connectors.

Customer reviews on DEXP TVs

Despite the fact that this company has been in our country for a long time, it has not yet succeeded in establishing itself among the population. However, these questions are more likely to the marketing department, since the quality of DEXP TVs remains at an acceptable level, which is noted by many owners.

Our list of the most popular DEXP TVs

Model Price Digital TV
h32d7200c 10000 Yes
u43d9100k 24000 Yes
u43d9000h 25000 Yes
h39d8000q 15000 Yes
h32d8100h 12000 Yes
h32d8000q 12000 Yes
h20d7200e 7000 Yes
h20d7100e 7000 Yes
f55d8100k 30,000 Yes
f49d8200h 22000 Yes
f49d7000c 19000 Yes
f40d7100m 15000 Yes
f32d7200c 12000 Yes
f32d7100c w 12000 Yes
f32d7100c 12000 Yes
f24d7200e 9000 Yes
f22d7200e w 9000 Yes
f22d7200e 8000 Yes
f22d7100e 8000 Yes

In addition, TVs are relatively inexpensive and will generally be affordable for most people. Taking into account the transition to digital television, most of the company’s models have long since switched to DVB-T2.

Manual search

If the automatic procedure does not give the desired results. For example, there are few channels or none at all, then you should try to search in manual mode. In this case, the procedure will be somewhat delayed, but the result will be the maximum possible at the moment.

  • First, we need to find out our frequency of transmission of digital channels on the interactive map of TsETV. We are interested in the channel number for both multiplexes (РТРС1 and РТРС2).
  • After that, SIMilar to the above screenshot, go to the TV DEXP menu and select “Manual DTV Search”.
  • In a special window for selecting parameters for manual search, we need to indicate the channel number that you previously specified on the CETV map. You need it After that, press the start button. This should be done for both parameters of multiplexes.

DEXP errors when tuning channels

In this case, we initially do not take into account those moments when the TV is obviously faulty. In other moments, situations may occur when, during the process of tuning, connecting or searching for channels, the TV begins to behave strangely or even starts to display error messages. There are already recommendations on this score, which we will give below.

Can’t select display mode

There are several display options on DEXP TVs. DTV. if you want to watch and tune digital channels. ATV. for analog TV. AV. when connecting a set-top box or audio equipment via RSA (tulips). HDMI. if an additional device is connected via an HDMI cable, for example, the same set-top box. PC. to use the TV as a monitor. USB. if you want to read information from a flash drive.

No signal strength and quality / do not show channels

  • Check the antenna connection cables. Perhaps the amplifier contacts are “damp” and need to be cleaned. You should also make sure that you picked it up correctly.
  • In the absence of a signal, poor-quality cables are often to blame. In this case, the signal does not have time to reach the TV due to the influence of interference.
READ  How to tune cable channels on your TV

Remote control does not respond / button does not work

Check the batteries. If the problem persists, replace the remote control. On some DEXP models, users report a very “hard” pressure. These are rather questions to the manufacturer.

Ohdpluginlibrary application error

Occurs when the TV software has been incorrectly updated or malfunctioned. You can solve it as follows:

  • Factory reset via the menu.
  • Installing a new software version.

Checking DVB-T2 on the device

Before trying to set up digital broadcasting, you need to make sure that this model can connect to this standard.

Old and new dexp

Can’t select display mode

DEXP TVs have several display modes. Which one to choose depends on the broadcasting standard that the user needs:

  • Select DTV to watch digital channels.
  • For analogue. ATV.
  • If the user connects the set-top box, then the AV mode is needed.
  • If the set-top box or some other device is connected via HDMI cable, then you need to select the HDMI mode.
  • To use TV as a monitor, PC mode is required.

Manual search

If the automatic procedure does not give the desired results. For example, there are few channels or none at all, then you should try to search in manual mode. In this case, the procedure will be somewhat delayed, but the result will be the maximum possible at the moment.

  • First, we need to find out our frequency of transmission of digital channels on the interactive map of TsETV. We are interested in the channel number for both multiplexes (РТРС1 and РТРС2).
  • After that, SIMilar to the above screenshot, go to the DEXP TV menu and select “Manual DTV Search”.
  • In a special window for choosing the parameters of manual search, we need to indicate the channel number that you previously specified on the CETV map. You need it After that, press the start button. This should be done for both parameters of multiplexes.

DVB-T2 set-top box

If your TV does not have a built-in tuner, you will need to purchase and install it separately. Having initially configured the receiver parameters, you can proceed to the channel search on the TV. The search can be performed both in automatic mode and in manual mode. In the second case, you will need to set the search parameters manually.

The aLGorithm of actions is as follows:

  • After selecting manual channel search, set the frequency, modulation and bit rate parameters.
  • Start the channel detection process with the confirmation button “OK”.
  • After the first found channel, press the “Next” and “Enter” buttons on the remote control.
  • Each channel found will be assigned a sequential digit, the search automatically stops at each stage.
  • To continue, click the “Next” button.

Broadcast standard

Before you start setting up digital television, you will need to determine which broadcast standard is advisable to use: it can be cable, satellite or terrestrial format. Since most modern TVs are already equipped with built-in receivers and decoders, you may not need to buy additional equipment. With a cable connection, you must purchase an access card and modulator from your provider and pay a monthly subscription fee.

The antenna is placed on the street towards the broadcast tower. A cable is laid from it, which is connected to the TV. For satellite TV, you will need to purchase a special dish and decoder. All digital broadcast standards reproduce high quality broadcasts, reaching Full HD and 3D.

To watch interactive television, you will need to install a special player. There are a variety of free IPTV applications on the internet. After downloading via Wi-Fi and installing immediately on the device, you can comfortably watch your favorite TV shows, as well as various additional features (not just viewing becomes available. you can stop the broadcast at a point of interest, as well as read information about it). Now developers are presenting players for different operating systems.

Another possibility is the connection of several devices to digital television using a network LAN cable.

Customer reviews on DEXP TVs

Despite the fact that this company has been in our country for a long time, it has not yet succeeded in establishing itself among the population. However, these questions are more likely to the marketing department, since the quality of DEXP TVs remains at an acceptable level, which is noted by many owners.

Our list of the most popular DEXP TVs

Model Price Digital TV
h32d7200c 10000 Yes
u43d9100k 24000 Yes
u43d9000h 25000 Yes
h39d8000q 15000 Yes
h32d8100h 12000 Yes
h32d8000q 12000 Yes
h20d7200e 7000 Yes
h20d7100e 7000 Yes
f55d8100k 30,000 Yes
f49d8200h 22000 Yes
f49d7000c 19000 Yes
f40d7100m 15000 Yes
f32d7200c 12000 Yes
f32d7100c w 12000 Yes
f32d7100c 12000 Yes
f24d7200e 9000 Yes
f22d7200e w 9000 Yes
f22d7200e 8000 Yes
f22d7100e 8000 Yes

In addition, TVs are relatively inexpensive and will generally be affordable for most people. Taking into account the transition to digital television, most of the company’s models have long since switched to DVB-T2.

Poor image quality

In this case, the procedure is as follows: check the operation of the antenna, as well as the integrity and operation of the cables that connect the antenna to the TV. In this case, the signal will not be able to arrive normally and there will be constant interference.

Checking DVB-T2 on DEXP TV

Before starting all work, you need to make sure that your Dexp model is adapted to receive digital television. To do this, the TV must work with the broadcast standard. DVB-T2.

You can check the availability of the possibility of accepting a digit in several ways:

    Enter your TV model on our website. To do this, select “TVs” in the equipment menu. The table will show many companies, you just need to enter the number of your device. If the search finds it, then you can safely proceed to the next section of the setup.

If you could not decide in the above ways, then you can ask a question in the comments, we will try to help you with your searches. If it turns out that the TV cannot work with the DVB-T2 standard, you will additionally need to purchase a digital set-top box.

Manual setting

  • If you left the menu, press the “Menu” button on the remote control and enter the “Channels” section again.
  • Select “Manual DTV Search”. The setup window will appear.
  • In the line “Channels” enter the number on the remote control, which will correspond to the next found frequency.
  • In the “Frequency” or “Band” item, you must specify a numerical value. You need to enter it in the line in which you need to enter data in megahertz (MHz). They are set using the “” and “” buttons from the remote control. These frequencies are unique for each region.
  • If you have cable or satellite television, then the list of frequencies and bands can be obtained from the provider by calling the hotline.
  • When you finish entering the parameters, the bar at the bottom will change showing the signal strength.
  • Press “Enter” on the remote.
  • Available channels on the specified frequency will be found. Do not forget that a different frequency must be specified for each multiplex.

Automatic channel tuning on Dexp TVs

First you need to make sure that the batteries are inserted in the remote control, and the TV is powered on from the mains. If before that TV was not connected to an antenna, cable or receiver, you must do this.

How to set up a TV, step-by-step instructions for connecting a digital TV:

  • If no tuner is available, you must first specify the digital source. Click the Source button. From the list, using the designations on the remote control “▲”, “”, “” and “”, you must select “DTV”. Press “Enter”.

REFERENCE. If you cannot find the Source button on the remote, skip this step. You will be able to adjust the source in a different way.

  • Press “Menu” on the remote.
  • Use the “▲”, “”, “” and “” keys to select the “Channels” section from the menu. Press “Enter”.
  • If you are using a tuner, then you need to click on the “Tuner Mode” item. If you have a satellite dish, select “Satellite”. If paid TV is connected. “Cable” or “DVB-C”. To watch free 20 channels, specify “Ether” or “Ether” and confirm the action with “Enter”.
  • If you are not using a tuner, select “TV Mode” from the list that appears. Use the “” and “” buttons to specify the mode as in the previous paragraph.
  • Find the “Auto Search” function. Press Enter. Depending on the model or your TV provider, it may be labeled “Auto Tuning” instead.
  • Confirm the action by pressing the “Enter” button.
  • In the appeared window of the scan type select “Full”. Network identification. “Automatic”. The search for available frequencies starts.
  • After auto tuning is complete, a list of the found TV channels appears. Make sure the number is as expected. If some are not found, you need to configure manually.
READ  How to tune channels on a dexp TV

If your TV does not support digital

In the absence of the required DTV-2 standard, the easiest and most inexpensive way to solve this problem is to purchase a digital set-top box. Its other names are tuner or receiver. Buying a new TV will also solve the problem.

The purchase of a set-top box will cost much less than a new TV. In addition, many Pay TV providers provide such devices for rent. With a set-top box, even the oldest TV can receive a digital signal.

Tuning digital channels on a DEXP TV

Digital television has become available to a wide range of users. There are many offices offering their services for setting up a TV. However, you can do it yourself. This article will show you how to tune digital channels on your Dexp TV.

  • Checking digital broadcast support
  • If your TV does not support digital
  • Automatic channel tuning on Dexp TVs
  • Manual setting
  • Deleting and sorting channels
  • Frequent mistakes and their solutions

Checking digital broadcast support

You can find out if your device supports this type of broadcasting at smotritsifru.rf. the official website of digital terrestrial television in the “All for reception” section. To do this, select Dexp from the list of manufacturer, then indicate the TV model.

You can also find this information in the documentation and on the product box. If it says that there is support for the DTV-T2 standard, then your TV accepts a digital.

A visual inspection of equipment is also able to answer this question. If on the back or side of the TV there is an input jack labeled Digital input, or just T2, then everything is in order.

Deleting and sorting channels

For convenience, you can assign any of them a specific number on the remote control or remove unnecessary ones from the list. This requires:

  • Select the desired TV channel from the list of found.
  • To remove it from the list, press the red button on the remote. If you change your mind and want to add it again, you will have to repeat the entire search and setup procedure from the beginning.
  • To move the TV channel to another position, press the yellow button of the remote control, then using the buttons “▲” and “” move to the desired position.
  • If you left the menu window, then use the “Menu” button, then select the “Settings”.
  • Click on “Channel Sort”. A special folder will be created and you will be prompted to enter a name for it.
  • Now you can edit the TV channels of this folder in the same way as in the list of found.

Frequent mistakes and their solutions

The main problems faced when setting up numbers for Dexp TVs are:

  • No screen image
  • Picture slows down

The reason is a weak signal. If there is a thunderstorm outside, just wait until it stops. If not, check the antenna mount and the cable entry between the antenna and the TV. If everything is in order, then you need to check the signal quality using the “Info” button on the remote control. If the “quality” value is less than 50%, and this value is not temporary, then you should think about purchasing an antenna amplifier.

In case you have Pay TV connected, call the provider. the problem relates to him.

  • Autosearch found few channels

If, instead of 20 digital channels, the TV found 10, make sure that the rest can be viewed in your region. This can be done on the site smotritsifru.rf in the tab with an interactive map. If all frequencies can be viewed, inspect the cable and antenna. If everything is in order with them, use the manual channel search.

  • Signal drops, “noise” appears

Check cables and antenna. Also, the problem may be a long distance to the repeater or the wrong direction of the antenna. Move the antenna and check the signal. If nothing has changed, your location may be too far from the signal repeater. Then you need an amplifier for the antenna.

  • OHDPluginLibrary Application Error

The reason is TV software failure. To solve the problem, you need to reset to factory settings through the menu. To do this, press the “Menu” button, select the “Settings” item, find the “Reset and Update” option and confirm the decision by pressing the “Enter” key. The device will reboot. After this step, you will have to perform the configuration again.

Sorting channels

3.5.2019 DEXP LED 22 Tomsk On the TV, channels were tuned with 11 digits, but it is not convenient to switch channels from 1.

Answers to questions on TV Dexp. How to set up a Dexp TV

Editing the channel list after setting up the TV Dexp

Highlight this option and press ENTER to enter the TV Edit Menu.
Press ▲ / to highlight the required parameter. To delete a TV channel, press the RED button.
To rename a TV channel, press the GREEN button (in ATV mode).
To move the TV channel, press the YELLOW button.
To set a pass to a TV channel, press the BLUE button.
To add a TV channel to your favorites, click the button with the heart.
To move one page forward or backward, press the CH or CH button-.

Dexp TV manual

Dexp TV manual for model Dexp 32A3200 contains information on how to connect a TV.
1. Unpack the TV and place it on a dry and flat place. When installing the TV, make sure the power is off;
2. Antenna plug of terrestrial, cable or satellite TV should be connected to RF input port of TV Dexp.
3. The output of an audio DVD player, or other equipment, can be connected to the AV input port of TV via an AV cable. Make sure all AV cables are connected in the correct order according to the color coding on the Dexp TV cabinet.
4. Component output (YPbPr) of DVD player can be connected to component TV input via AV cable. Dexp TV component and audio input cannot be used SIMultaneously.
3. The output of the audio DVD player can be linked to the AV input port of TV
5. To connect the computer to the Dexp TV, connect one end of the VGA cable to the port on the computer and the other end to the VGA port on the TV Dexp, and tighten the connector latches clockwise at each end of the cable. When connecting the 15-pin VGA connector, insert it carefully so as not to damage the pins.

Dexp TV remote control

The figure shows the Remote control for the Dexp TV, its function buttons and their purpose:

I: Turning the TV on and off
2. MUTE: Mute / Unmute
3. STILL: Pause: Hold teletext on screen. : Stop (in USB / PVR mode).
4. RADIO: switch between TV and radio modes. (in DTV mode).
5. TXT: Enter teletext mode, press again to enter mixed display mode and again to exit. : Play / Pause (in USB / PVR mode).
6. SIZE: Selects various formats. : Select teletext size in teletext mode.
7. Colored keys: red / green / green / yellow for teletext: rewind (in USB mode). : Fast forward (in USB mode). : Previous recording (in USB mode). : Next entry (in USB mode).
8. SOURCE: Select signal source. : Display hidden information in teletext.
9.MENU: Call up a pop-up menu with various settings.
10. Right / Left / Up / Down: Navigation keys
11.ENTER: Select and apply parameter settings.
12. INFO: Display program information on the screen. i: Skip to content.
13. EXIT: Exit the menu 14. INDEX: Go to the list of recordings (in DTV mode)
15. VOL / VOL-: Press to adjust the volume.
16.CH / CH-: Press to select channel.
17.LIST: Press to call up the channel list.
18.Numeric keys: Select channel or password.
19. AUDIO (∞I / II):
20.DVB: Antenna selection.
21. SLEEP: Sleep timer. The TV will go into standby after the time has elapsed.
22. LIST:
23.: Return to the last program.
24. EPG: Electronic program schedule in DTV mode
25.: Exit teletext mode
26. REC: Press the button to start recording
27.: Switch on subtitles or subpages. (
28. USB: Go to USB source.

READ  Broadcast Laptop Screen To TV Over Wi-Fi

On our website you can download the TV Remote
location and designation of remote control buttons, as well as instructions and user manual

How to set up a Dexp TV

Dexp TV. Dexp TV remote control.

How to tune digital channels on your TV

You are using cable TV. You have already configured all digital channels, in order to watch them, you need to purchase a CI card and conclude an agreement with the provider. Cable digital television is paid, you will need to pay monthly.
DVB-T2. it is an opportunity to watch digital channels of terrestrial, not cable TV for free. To implement it, you need to purchase your own antenna, place it in the zone of receiving waves from the Ostankino TV tower and orient it correctly. If you want to take advantage of this opportunity, the TV will need to be reconfigured (automatic tuning is fine), terrestrial and cable channels are in different tuning positions.

Entering the main menu Dexp 9000. button with the image of the “House”. In some models, you must first switch to DTV mode (Input button), and already in this mode, readjust.

4.17.2019 DEXP F43D8000K Korsakov How to set up ttvatv? I have already tried everything that was on the Internet, but did not give any results. There is no way to enter home, the OHD pluginlibrary error crashes. There is no channel “settings” item in the menu.
8.20.2019 Dexp f40d7100m Voronezh TV in dvb-c mode does not look for channels, even tried through a set-top box, does not find
10.28.2019 Dexp H32D7100E H32D7100E Saint Petersburg Digital channels cannot be tuned

TV without antenna and cable

Wireless television has obvious advantages over cable television. Several devices can be connected SIMultaneously from one access point. The wires do not get tangled and do not interfere with the user, besides the mobility of the receivers allows them to be installed in any convenient place.

How To Tune A Dexp TV Without Antenna

The owners of modern devices are interested in how to properly connect and set up a TV without an antenna, whether it can be done independently and what to do in case of communication problems.

How and what is wireless television used for

The possibility of transmitting a moving picture over a distance has been of interest to inventors for a long time. In 1843, Alexander Bain created a facSIMile machine. the progenitor of modern television receivers.

In the twentieth century, engineers perfected the invention. Familiar TVs appeared, in which an electrical signal was converted into a light signal by means of a kinescope.

The beginning of the 21st century was marked by a revolution in the TV market. bulky tube models replaced thin elegant plasma panels and LCD screens.

At the same time, this coincided with the advent of Wi-Fi, a wireless method of signal transmission. High-frequency radio waves communicate it to receivers. computers, televisions, cell phones and other electronic equipment.

Wireless television is no longer an exotic novelty. Films and programs can be watched at home or while traveling, on a large TV screen, computer, laptop or smartphone.

over, it is possible to watch the programs of interest at a convenient time, in a comfortable environment. To do this, you do not need to buy additional equipment, it is enough to have access to the Internet and a receiver that supports Wi-Fi.

In this you will learn more about TVs:

The first Wi-Fi was created by the radio astronomer John O’Sullivan from Australia. Initially, the acronym stands for Wireless Fidelity. Now the term is used to refer to local networks that transmit a signal using radio waves within the same facility or a limited area.

Typically, a Wi-Fi network has at least one access point and a client. If there are two users, the point-to-point option can be used. a direct connection between them using network adapters.

The access point sends its SSI network identifier at a rate of 0.1 Mbps using special signal groups. packets.

Knowing the SSI of the network, the client can use this access point. If there are several, the receiver selects an option based on the signal strength. The consumer sets the criteria himself.

  • reducing the cost of deploying or expanding the network;
  • use in places where it is impossible or forbidden to lay a cable. outdoors, in buildings of historical heritage;
  • often the signal transmission rate is higher than when using a cable connection.

In crowded places. transport hubs, shopping centers, libraries, cafes. free hot spots have been created to access the most popular global network.

Each TV has its own unique settings

Wireless TV Settings

So that the owner knows how to set up a TV without a cable and antenna and can do it on his own, recommendations are given in the instructions for it.

The aLGorithm looks like this:

  • When you connect the AC adapter, a menu with settings appears in the TV menu. You need to click on the line “wireless network”.
  • Then choose from three options. “setting from the list of access points”, “WPS-button mode” and “network setting”. In the first case, they enter the address of their point, in the second, the TV itself will offer a list of coordinates. In the third, access opens only to information stored in the home computer.
  • When the second option is selected, the desired point is indicated in the list of available networks.
  • If the screen prompts you to enter a security key, enter the password.
  • Press “OK” to establish wireless connection.

If you have problems

Wi-Fi may not work for various reasons. Failure to receive a digital signal is often associated with settings problems.

If the TV does not show and does not pick up the signal, you can try to fix the errors yourself:

  • Reboot TV and router. To do this, they are disconnected from the network for a few seconds.
  • Enter manually data about the access point from the local range.
  • Reset TV settings and restore to factory settings.
  • Connect in another way. enter the IP address of the router and the password (indicated on the sticker on the bottom of the device) in any browser, go to the “WPS button mode”, activate the function.
  • Change the position of the router.
  • Replace the built-in adapter with an external one.
  • Update TV Firmware.
  • Check and correct the parameters in the router settings. The device may be blocking the connection because filtering mode is on.

If the actions taken did not lead to the elimination of the problems, it is recommended to contact the service center.