How to set up Internet on TV via cable

How to set up a TV with “Dynamic IP”

If you have the “Dynamic IP” protocol, the Internet on the TV will be configured automatically after connecting the cable. This will be indicated by a message on the screen “Connected to the wired network”. If the message does not appear and the Internet does not work, proceed to manual debugging (for example, Samsung Smart TV):

  • Go to the device menu. Select the “Network” block.
  • Open the item with network settings.
  • For the “Type of network” parameter, specify the cable connection.

internet, cable

Click on “Connect” to establish a connection

For TVs from other manufacturers, the setup principle is the same, but there will be a different interface. Some sections may have the same name. Most importantly, find the block with the network or network connection settings (usually marked with a globe). In LG, for example, you must first click on “Set up a connection”, then on “Set up manually.” Then select a wired connection.

Click on the pink button “Set up a connection”

Through a router

If you decide that you need an intermediary in the form of a router, do the following:

Using a special cord, you need to connect the router to the TV

Setting up TV with a wired connection directly or through a router

After the physical connection, you need to configure the TV to receive an Internet signal.

Router or direct connection. what to choose depending on the Internet protocol

The most important criterion that determines the type of cable connection is the protocol. If you have a dynamic or static IP, you can safely connect to your TV directly. In this case, a connection by cable and through a router will be available.

If you have PPPoE, L2TP or PPTP, only a router will work here. The TV does not recognize these types of connections.

Diagrams for connecting a TV by cable

We will show and tell you how to connect a TV to a router or just to a cable from an Internet provider.

Pros and cons of this connection method

What good can be in a cable Internet connection in general? Why this bunch of wires, if you can use “Wi-Fi”? Yes, you can, but firstly, not all TVs have built-in Wi-Fi modules. If you are an adherent of wireless connection, but the TV module does not have a TV module, you will have to buy it separately.

If you need to use the Internet not only on TV, but also on PC and phone, connect TV to the Internet using a cable through a router

Secondly, data is transmitted over the wire much faster than over Wai-Fay. Almost all routers cut the speed. Plus, they have to distribute a signal to several devices at once. the signal and speed are shared between the participants of the local network.

Thirdly, the cable connection is more stable than the wired one. Data transmission failures will occur less frequently.

Network cable can be connected directly to PC

The disadvantage of the method, of course, is the number of wires. They do not always fit into the interior. Plus, it’s inconvenient. If the router and TV are far from each other, even more so. You will have to either buy a long cord, or rearrange the router closer to the TV.

If you do not have a router and do not want to use it, but you have a provider’s cable, you can insert the cable directly into the TV. You don’t have to buy a router. If the TV is not equipped with a Wi-Fi module, direct cable connection will be the only budget option.

How to set static IP and DNS on TV

If you connect the Internet directly and use the “Static IP” protocol, after the basic TV setup (which was described in the previous section), you need to register the data from the contract in the TV settings: IP address, DNS addresses. Where to write them:

  • After the basic setup of the wired connection, go to the “Connection Status” section.
  • Next click on IP Settings.

Internet on TV: how to connect using a cable

Modern TVs with Smart TVs can be connected to the Internet. Various sites, applications, viewing and listening to content online become available to you from the TV screen. In order for the TV to have access to the network, you can simply go to the home Wi-Fi access point, or you can use a wired connection. through the router itself or a direct connection (Internet cable directly to the TV).

How to connect Samsung Smart TV to the Internet with a cable

Smart TVs have become very popular due to their capabilities. Internet access directly from the TV allows you to watch videos online and access a lot of information on the network. Various applications make it easy to find your favorite video and open up new horizons for the user. Samsung has been improving the Smart functionality of its TVs for a long time. Obviously, to realize all the capabilities of “smart” TVs, you need to connect to the network. However, not all users know how to connect Samsung Smart TV to the Internet via cable.

The cable connection allows for a reliable connection with good data transfer rates. It is necessary for Honor that in order to avoid problems with the speed of page loading, as well as the speed of applications and services, you must have an Internet channel with good bandwidth. If your internet speed is less than 10 Mbps, then problems may arise. There are several ways to connect Samsung Smart TV to the Internet using a LAN cable. We will analyze each of them in detail.

Also, after connecting, in some cases, it is necessary to manually configure the Internet connection parameters. In most cases, the setting is automatic, but it may not happen. Don’t worry too much, you won’t be left without the Internet. After all, we will also analyze all the necessary settings that will need to be made, and describe the problems that you may encounter.

Let’s take a closer look at how to connect Samsung Smart TV to the Internet via a cable. The first way is to use a standard LAN cable to connect the Ethernet connector on your TV and on an external modem.

The second method involves using a router. But we will not connect using a wireless connection, but using a cable. Use a LAN cable and connect the Ethernet connectors on your TV and router. The router must first be connected to an external modem and configured.

The third method involves direct connection of the TV to the provider’s network. Using a LAN cable, connect the Ethernet connector on your TV and the Ethernet connector of the provider’s network, which, in most cases, is located on the wall or in another specially designed place.

Thus, we have listed all the situations that you may encounter if you want to connect your Samsung Smart TV to the Internet via a cable. Next, we will analyze the features of setting up a connection.

Internet setup on Samsung Smart TV

After you have made a wired connection, you need to configure the TV. Press the “Menu” button on the TV remote control, then go to the “Network” tab and find the item “Network Settings”.

A window should open on the TV screen, the appearance of which will depend on the specific model of your TV. Don’t worry, the semantic windows are preserved. In the window that appears, click “Next”.

Since we want to connect Samsung Smart TV to the Internet via a cable, select the type of network connection “Cable” and click “Next”.

The internet connection is now complete. The TV will receive all settings automatically. A successful connection message appears on the TV screen. If there are no problems, click “Next”. If the Internet has not connected to the TV, then you need to manually configure the connection. To do this, select the item “IP Settings”.

A settings window will appear in front of you. In the “IP Mode” and “DNS Mode” items, the “Automatic” mode should be set by default. You must enter “Manual” instead. If you want to properly connect Samsung Smart TV to the Internet via a cable, you need to find out all the necessary settings from your Internet provider and enter them manually. The underlined options are the required parameters. If you have a computer that is connected to the Internet by cable, you can view the necessary parameters on it.

READ  How to tune digital channels on Sony Bravia

On your computer, find “Local Area Connection” and click “Details”. A window will appear with all the settings. After that, the TV connection to the Internet should work.

If these recommendations did not help you connect Samsung Smart TV to the Internet via a cable, then write about the problems that have arisen in the comments. We will look at each specific case.

Features of customizing different models

Smart TV setup options vary by TV model.

Most LG models require registration in the Smart TV system for correct operation, without which even installing applications will be impossible. Having entered the main menu of the TV, in the upper right corner you need to find a key that allows you to visit your account. Usually, a username and password are simply entered here, but when using Smart TV for the first time, you will first have to click on the “Create an account / Register” button. In the window that opens, the username, password and e-mail address are entered into the appropriate forms. To confirm the data, you will need to use a laptop or smartphone. When registration is complete, you will need to go to the same window and re-enter the data. This completes the setting of the technology.


To set up a Samsung TV, you first need to open the Smart Hub menu using the remote control by clicking on the cube image. That should be enough. You can check the correctness of the settings by going to any of the installed applications. Successful start-up symbolizes quality installation.

By the way, many models also require new user registration, which is described above.

How to connect and set up Smart TV?

Many models of modern TVs go on sale already equipped with Smart TV technology, which allows you to search online, watch a movie, and even chat via Skype directly through the TV interface. However, Smart TV requires proper connection and setup to work properly.

How to connect?

In order to start working with Smart TV, you need to establish a connection between the TV itself and the Internet. This is done in two ways:

  • wireless, implying a connection to Wi-Fi;
  • wired, requiring the mandatory use of a cable.

The first method is more preferable, since the resulting compound has a much higher speed. It is easier to turn on such a scheme and you don’t have to solve the rather tedious issue of placing the cable in the apartment. Nevertheless, it should not cause any special difficulties to establish and cable connection.

To create a wired connection, you need to select a LAN cable of the required length, and then connect it to the TV, modem and Ethernet port.

This is done in the following way: one end is inserted into the Ethernet jack on the TV, and the other is connected to an external modem. The modem itself by this time should already be connected to the Ethernet port in the wall. The device quite quickly recognizes the new connection, and the connection will be established, after which it will be possible to activate Smart TV on the TV immediately. This method has quite a few drawbacks. For example, the equipment used is quite difficult to transfer somewhere, since it all depends on the length of the cable.

over, the quality of the connection is highly dependent on the condition of the wire, and the slightest damage to it leads to the failure of all work. Quite often, over time, the sheathing of the cord will crack, exposing the hazardous contents, increasing the likelihood of electric shock. And, of course, it is not always possible to hide the wire under the floor, baseboards or behind cabinets, and it remains ugly to lie on public display. The advantages of the cable method include the simplicity of the circuit, as well as the absence of the need to additionally adjust the TV signal. Most of the problems occur due to the condition of the cable, which means that its replacement leads to the elimination of problems. The special wire costs little, and connects in less than 1 minute.

Wireless connection of Smart TV via Wi-Fi is possible only if there is a Wi-Fi module built into the TV, which is responsible for signal reception. In the absence of a module, you will additionally have to buy a special adapter that looks like a small flash drive and connects to the USB port of the TV. The first step is to turn on Wi-Fi in the apartment, and also either connect the adapter, or make sure that the built-in module functions smoothly. Next, a search for available networks is started through the TV and a connection to one of them is made. If you need to enter a password or security code, then you need to do this. As soon as the TV is connected to the Internet, you can proceed to setting up Smart TV.

If necessary, it will be possible to use Smart TV technology using a computer. In this case, you will need either an HDMI cable or a working Wi-Fi. However, in the first case, the TV itself will not get access to the Internet, but it will be possible to turn on video recordings on a computer, and see the result on a large screen. In the second case, the computer simply performs the function of a router, and therefore the computer gains access to the online space.

It should be added that sometimes Smart TV technology requires the use of a special set-top box. This module is connected to a TV using an HDMI cable or a combination of a cable and an HDMI-AV converter. “Docking” via USB is also possible. The equipment is charged either from the TV itself or from an adapter plugged into an outlet.

Before connecting the set-top box to the TV, it is recommended to first de-energize the equipment, and then connect the appropriate connectors with a cable.

In the event that the set-top box is connected to the router using a LAN cable, it is better to choose an RJ-45 cable. Having connected the two devices, you need to open the media player menu and find the network settings. Having marked the “wired connection” or “cable”, it will be enough to press the connection button, after which the automatic setup procedure will begin.

Sony bravia

When connecting Smart TVs on Sony Bravia TVs, you have to act a little differently. First, the “Home” button is pressed on the remote control, which allows you to get to the main menu.

Further, in the upper right corner, you will need to click on the suitcase image and go to the “Settings” tab.

In the expanded menu, you will need to find the “Network” sub-item, and then select the “Update Internet Content” action. After restarting the network connection, the TV will automatically complete the Smart TV setup.

How to set up correctly?

It should be mentioned that the Smart TV setup differs depending on the TV model you are using. Nevertheless, whether it was a connection via a router or a cable, whether it happened without an antenna, if all the components of the circuit are connected correctly, a message should appear on the screen that the device is connected to the Internet. Next, in the main menu, select the “Support” section and activate the Smart Hub item. By launching the browser, you can start installing widgets, that is, auxiliary applications for working on the Internet.

Possible problems

Despite the seeming simplicity of Smart TV operation, users often have the same problems with connecting and setting up the technology.

  • If there is no contact with the worldwide network, you can go to the main menu, then select the “Network” section, and in it there is “Network Settings”. Immediately, you should see an automatic configuration prompt, which it is better to agree with by clicking “Start”. In the event that the connection is still not established, you need to go to the “Network Status” tab. Going to the “IP Setting” section, you should start automatically obtaining an IP-address, or even enter it yourself. The easiest way to get the required data from the provider is by making a phone call. Sometimes a simple reboot of the device can cope with the lack of an Internet connection.
  • In the event that the problem lies in the adapter settings, then they just need to be double-checked. If the user has the ability to use the WPS system, then you can try to connect the device automatically.
  • Blurry images and screen noise appear as a result of insufficient processor power. It will not work to correct the situation on your own, since in this case a complete replacement of the device is required. If your browsing problems are the result of slow internet speeds, then it may be better to contact your provider and change the existing service package. Pages take too long to load when the router is located away from the TV. Fortunately, the solution to this problem is the easiest.
  • When the TV turns on and off on its own, then it is logical to start the repair by checking the outlet. often loose contacts are to blame. Next, the TV’s settings are checked and a software update is installed. If, despite the correct settings, Smart Hub is blocked, you can try to work with the service menu. However, this problem most often arises when buying from unofficial representatives and developers or abroad, so it is unlikely that it will be possible to solve it on your own. When adjusting the settings, it is better to save each step on the camera in order to be able to return everything back.
  • If you have problems with your Android Smart TV, you can reset it to factory defaults. Experts recommend such a radical method only when the device freezes, restarts, does not connect to the Internet and slows down. In the first case, you need to open the set-top box menu and find the “Restore and Reset” section in it. After the backup, the “Reset settings” item is selected and the “Data reset” is activated. The device will automatically shut down and reboot.
  • In the second case, a special Reset or Recovery button is sought on the body of the set-top box. It can be hidden in the AV output, so you need a toothpick or needle to press it. Holding the button, you need to disconnect the power cable for a few seconds, and then connect it back. When the screen blinks, it means that the reboot has started and you can release the button. “Wipe Data Factory Reset” is entered into the opened boot menu and “Ok” is confirmed. Then click “Yes. Delete all User Data”, and then select the item “Reboot system now”. A few minutes later, the system should reboot.
READ  What Does It Mean Connected Without Internet On TV

How to set up Smart TV, see below.

How to set up the Internet on a computer via a cable

Immediately after connecting the cable, you need to pay attention to the icon of the network devices. If there are no additional indicators on the icon, then most likely your computer is already connected to the global network. However, the most common option is a yellow exclamation mark over the network connections mark. This means that the network card has recognized the cable, but there is no internet connection. In this case, additional connection settings will be required, which will be discussed below. And the last option is a red cross-shaped indicator over the network connections sign. This indicates that the cable is not plugged into the network card. In this case, make sure that the wire is inserted all the way (usually accompanied by a characteristic click) and if the situation has not changed, try replacing the cable. If this does not help, then connect to another device. It is possible that the network adapter itself is not working correctly.

To configure the connection, right-click on the network connections icon and select “Network and Internet Settings”. In the window that appears, click “Configure adapter settings”.

Go to the connection properties of your network card.

In the menu that opens, find the item “IP version 4 (TCP / IPv4)” and select its properties. Then it all depends on the type of network construction used by the provider.

If your ISP provides a dynamic IP, then you must choose to automatically obtain an IP address and DNS server. If the IP is static, then the operator must provide you with all the necessary data to fill in the fields.

How to connect a laptop to the Internet via a cable

We connect the laptop directly via a cable and set up an Internet connection.

The main advantage of a laptop over a classic desktop computer is its portability. All laptop developers dance around this. The devices are made not only light and compact, but also energy efficient, so that the user is tied to any place as little time as possible. For example, when a gadget needs recharging. The same goes for a wireless Internet connection: without it, you can forget about portability. But there are times when you need to connect to the World Wide Web directly using a cable. For example, if the router is out of order. Today we will tell you how to set up the Internet on a laptop via a cable.

How to connect to the Internet via cable: method

According to the principle described above, the connection is made directly. This does not require additional cables. The wire that the provider held out to you just needs to be inserted into the network card. After that, you can proceed to the next step. setting up the connection.

PPPOE connection setup

Some providers, instead of IP addresses, provide the user with authorization data. login and password. In this case, you will need to create a new connection type. To do this, press the Win R keys and in the window that appears, enter the command: control.exe / name Microsoft.NetworkandSharingCenter

In the window that appears, select the item “Create and configure a new connection or network”.

And at the end, enter the data that the provider told you when connecting. If necessary, upon request to the service center, the data can be re-provided.

After that, click the “connect” button and the Internet should appear. As you can see, all the methods described above are very simple. The setup is always the same regardless of the type of device (PC, laptop, netbook, etc.), so you will probably get it right. Now you know how to connect and configure the Internet on a computer via a cable. However, this is not all. It happens that after the above actions, access to the World Wide Web does not appear.

How to connect the Internet via cable: method

The connection itself does not require any special skills, even a beginner can handle it. If you need both Wi-fi and any device connected with a cable in the house, then this method will suit you.

Almost any router comes with an Internet cable with RG 45 connectors at both ends.

One end must be plugged into any available LAN port on the router. Depending on the model, there may be several such connectors, through which one to connect is not so important. The other end must be inserted into the network card of the PC (or laptop). The twisted pair cable, which is pulled by the provider when a new subscriber is connected, is inserted into the WAN connector in the router. On any device with wi-fi on board, there are indication lights that show which connector is connected. If you did everything correctly, then the lights will be on (usually green).

Pros of a wired connection

We agree that Wi-fi is much more convenient than connecting via cable, but the latter has a number of undeniable advantages:

  • Internet speed when using a wireless LAN is much slower than when using a cable.
  • The router acts as a kind of intermediary between the source of information on the network (server) and the receiver (your PC), which leads to increased latency. This point can be important for online gamers. When connecting directly, ping (latency) will always be lower than when connecting using wi-fi.
  • The wire can be extended to any point in the apartment, but the coverage area of ​​routers, especially budget ones, leaves much to be desired. In addition, the wire is much cheaper than any repeater that amplifies the wi-fi signal.

What to do if the Internet does not appear

There are some of the simplest preventive actions for troubleshooting:

  • Diagnosing network problems is often useless, but in some cases it can really help. To launch it, click on the icon of network devices in the lower right corner of the desktop, select the appropriate item and wait for the end of the search process.
  • Resetting TCP IP parameters can sometimes be helpful. Run Command Prompt as administrator and enter the following commands one by one without punctuation marks: netsh winsock reset; netsh int IP reset. After restarting your computer and check the connection.
  • Another simple but effective way is to uninstall the network adapter drivers. To do this, find your network card in the device manager, right-click on the icon and select “Remove device”. Do not worry, the next time you start, the operating system will automatically restore the latest driver from the embedded database. This action avoids software conflicts with your network equipment.

Pros and cons of IPTV

Interactive television IPTV opens up several useful additional functions for Smart TV owners:

  • recording of television broadcasting;
  • pause and rewind the air.

The functionality of IP-television is not limited to the traditional set of federal and regional channels. Even the extended broadcasting of cable or satellite providers can be inferior in the number of available Internet TV channels. All this applies primarily to pay Internet TV.

You can also watch TV channels over the Internet for free. Self-connection to unencrypted networks allows you to customize the display of 150 TV channels, including educational and thematic programs. Mostly this service is included in the standard set of services of Internet providers, but you will not be able to find really high-quality content.

An obvious advantage of IPTV is the absence of the need to purchase expensive equipment, which is required to connect satellite television. All kinds of receivers and antennas are also not required. Mostly users have to pay for related work:

  • setting up your TV and equipment;
  • cabling;
  • Additional services.
READ  Sony TV Wi-Fi Connected Without Internet

Of course, all-Russian companies include such minor work in the cost of connection, but local providers charge subscribers an additional fee.

You can set up interactive television not only on a TV, but also on other devices:

  • tablets;
  • PC;
  • smartphones;
  • Smart set-top boxes.
  • viewing the stream using special Playlists;
  • setting up channels, creating lists with selected content from them;
  • recording a video program with saving to a media file;
  • display of volume, record indicator;
  • TV program viewing and recording planner;
  • background saving in multiple threads;
  • remote control of the content playback process;
  • multichannel sound.

Of course, IPTV also has certain disadvantages. Periodically, the signal is cut off, mainly due to the low speed of the Internet. For proper content transfer, a connection with a speed of 10 Mbps or more is required.

As for other disadvantages, they are not so significant. Signal transmission over the Internet Protocol is a really effective technology. Owners of outdated smartphones, tablets, computers, TV may face certain difficulties. The point is that these devices may not support some functions.

What is IPTV

The abbreviation IPTV stands for Internet Protocol Television, which in English means television over the Internet protocol. The technology also provides for the use of digital packet data transmission. It should be noted that Internet TV and IPTV are significantly different. In the first case, you only need to connect to the World Wide Web to watch TV.

For the correct operation of IPTV, the Internet protocol is also involved, but this is far from the only condition. The broadcasting process is controlled by the provider, in some cases using closed channels.

Why watch TV over the Internet

Digital TV is the optimal broadcast technology. Data transfer is carried out promptly without loss of quality. That is why the decision was made to abandon analog television. As for IPTV, this technology is fundamentally different from the above methods of signal transmission. Data stream is transmitted via Ethernet cable.

Television over the Internet on the TV can be configured using the appropriate services of providers. Many companies provide access to an unlimited number of channels at maximum resolution. Subscription is accompanied by additional services:

  • watching new films, TV series, cartoons;
  • announcements of television programs, new films;
  • detailed TV program.

IPTV is an interactive technology with online feedback and surfing the internet. In this component, this type of broadcasting is noticeably superior to other methods of channel tuning: analog, digital, cable and even satellite. The user will be able to in real time:

  • use video communication via Skype, Viber and other applications;
  • run all kinds of services, video games;
  • send messages;
  • surf the internet.

Given these arguments, it becomes clear why users prefer Internet TV.

How to watch TV channels over the Internet on a Smart TV?

The owners of modern Smart TVs are increasingly interested in the question of how to set up IPTV for comfortable viewing of popular channels? This is streaming technology. Providers offer similar services. However, you can set up broadcasting yourself, but first you need to understand what IPTV is.

Installing the program on the TV and setting it up

Smart TVs allow you to use a wide range of different software. The main thing is to know how to properly dispose of the available opportunities. The developers have created many useful applications for watching TV. However, in the process of installing software, you need to take into account the model and functional features of the TV. The region of residence also matters.

For example, some operating systems offer access to a wide list of preinstalled programs, while on other models the software must be installed independently. This requires a stable internet connection. You can connect to the network using an Ethernet cable or Wi-Fi.

If the software was previously downloaded to a laptop, PC or tablet, then you can install the software on the TV from a flash card.

How to connect IPTV for free? The process begins with the installation of the corresponding application. Create a personal account in the program, and then log in to the system. The software may differ, but the TV tuning algorithm remains unchanged. To give users a real idea of ​​how to watch TV over the Internet on TV, consider a specific example.

Samsung Smart TV owners primarily use the Fork Store App Market. This program can be used on TVs from other brands as well. The software is convenient for efficient formatting of TV channels, you can sort them and create a list of “Favorites”:

  • Go to the official website of software developers. Forkplayer.TV.
  • Select brand name and TV model.
  • Read the instructions for the application.
  • Open the Fork Store App Market.
  • Select the SmileBY application from the drop-down list.
  • Reboot your TV.
  • The SmileBY widget will appear in the menu of available applications.
  • Turn on the program, and then select the first item in the list.
  • Go to the “Onlier Playlists” section.
  • Open the “Segaz” folder. Available Playlists are displayed in this directory.
  • Launch one of the available Playlists, for example, Rostelecom.
  • If a certain channel stops working, you can find it in another Playlist.
  • Turn on any of the available TV channels to watch.

At the bottom of the screen, a menu is displayed for quick tuning and sorting the list of found TV channels. You can create a favorite list by pressing a few buttons.

It is simply pointless to consider absolutely all applications with which you can configure IPTV. The list of programs will change depending on a number of important factors:

  • the location of the provider and user;
  • availability of regional TV channels;
  • TV brands and models.

Now you know how to tune channels on your TV over the Internet. Remember that IPTV control is carried out using a regular remote control. The number of available channels is determined depending on the Playlist used. Free lists contain up to 150 channels. For a wider assortment, you need to subscribe.

Each user can edit Playlists and even create their own. However, this requires special skills.

How to watch TV on a computer

There are several ways to watch TV online on your computer. The simplest and most effective option is IPTV. To set up TV broadcasts, you need to download the VLC Media Player, and then download the Playlists. When the player is installed on a laptop or computer, and the list of TV channels has been downloaded, open the Playlist in VLC. That’s all, you can enjoy watching.

The obvious advantages of setting up IPTV on a computer:

  • ease of customization;
  • no restrictions;
  • access to channels that are not available on all satellites;
  • no monthly fee.

If for some reason the considered option is not suitable, you can use alternative methods. Download special software to your computer. There is really a lot of software, but really working applications can be counted on the fingers of one hand. Pay attention to the “Eye TV” utility. It is a program with an intuitive interface. The utility takes up a minimum of free space. Install the software, then you can watch TV. Registration and setup of channels is not required.

The third option is perhaps the least effective. viewing channels online. You just need to open a dedicated website. Finding a portal in a search engine will not be difficult. Online browsing in the browser creates an additional load on the computer, which can cause freezes. Another disadvantage is the large amount of ads.

Where to get Playlists

To watch TV channels on TV via the Internet, you need to use special Playlists. Free channel lists on some models are embedded in pre-installed applications. If your provider provides IPTV service, then free Playlists can be requested from him. The content can also be downloaded from the Internet, but this method carries additional risks:

  • poor image quality;
  • unstable display of TV channels;
  • periodically some channels simply stop working.

You can download free Playlists to your TV from dedicated websites, but this is not the safest way.

There are tons of proven resources that provide access to stable Playlists that are updated automatically. It is advisable to use such portals.

How to watch TV on your phone

Watching TV channels is possible not only on PCs, but also on smartphones. Modern mobile technology is absolutely in no way inferior in performance to computers and laptops. Absolutely all of the above methods are also suitable for phone owners. For example, on smartphones running Android and iOS operating systems, you can install VLC Media Player. Then just download the Playlist. Everything is ready, you can watch the channels.

An alternative way is programs for watching TV on the phone. There are also a lot of them, but the work of free applications leaves much to be desired. Therefore, the fact that you will have to subscribe cannot be ruled out.