How to disassemble iPhone 6 at home

Preparation and selection of tools

disassemble, iphone, home

If you are still going to make repairs at home, then the next detailed “manual” is for you. Before starting work, you must realistically assess your capabilities. After all, if you are not competent enough in this matter, then you can cause irreparable harm by your actions. But still, all the recommendations are clear and with due attention and care, you will be able to repair your iPhone 6.

Attention: starting repairs at home will void your official manufacturer’s warranty.

To work, you need special tools:

  • Phillips screwdriver
  • vacuum suction cup;
  • special star-shaped screwdriver;
  • plastic or wooden stick to work with the train.

All of the above tools are sold as sets or separately. So it won’t be difficult to get them for iPhone 6 repair.

How to replace the display on an iPhone 6 at home

The owners of well-known apple smartphones, like users of other brands, face screen breakage. Indeed, despite its high cost, the fragility of phones still remains a minus of touch cell phones. Screen replacement remains the most requested service in telephone workshops. But there are those who are not at all afraid to open the lid and climb inside to fix it. Therefore, it is for such home craftsmen that a step-by-step guide is presented on how to change the display on an iPhone6 ​​by yourself.

  • the phone fell and the screen was broken;
  • getting water or moisture inside the smartphone;
  • the display has scratches and much more.

Of course, you can take your favorite gadget to a service center. But there are some downsides here. First, it takes quite a long time. Sometimes, such repairs can last from several weeks to months. In addition, the cost of such a replacement will most often be very high.

Step-by-step instruction

When everything is ready, it remains to find out how to replace the display on the iPhone6 ​​using the detailed instructions.

The first step is to turn off your iPhone 6 completely. This step is mandatory because you must prevent electric shock that may occur during operation. The fact is that even the smallest blow can harm the elements of the smartphone and affect their functioning.

Begin to gently unscrew the phone cover from the front side. This requires the use of a Torx screwdriver. Unscrew the Pentalobe screws one by one (2 pcs.). They are located near the Lightning connector.

Take a vacuum suction cup. Handle it carefully and use it to detach the display module from the case itself. Take care not to damage any of the cables that connect the two parts of the device.

Next is the turn of a Phillips screwdriver. Using it, detach the screws that hold the metal plates. They are required to protect each loop. Remove the plate from its place.

Take a stick made of plastic or wood and, being careful and careful, lift each train. Thus, you can separate the front panel and the body of the gadget.

Now you need to start unscrewing the screws that hold the cable protector for the camera and speakers. A wooden or plastic stick is also useful here. With its help, it is necessary to remove the train and detach the components.

Now it’s the turn of the Home button on the iPhone 6. It also needs to be disconnected. Remove the screws that hold the metal plate. And already with a stick, lift the mechanism to detach the cable.

Removing the home button will reveal screws (2 pcs.). They hold the screen. By unscrewing them, you can remove the screen.

Next, the old screen is directly replaced with a new one. After the display module is installed in its place, the instructions are similarly followed from the last step to the first.

You will have a working iPhone 6 if you followed all the steps clearly and were extremely careful. As you can see, replacing the screen is not as difficult as it seems at first glance. On the Internet, you can find many practical videos and detailed photos, with which the replacement will be more confident. In general, the process of replacing the screen takes about half an hour on average.

It is better to use original parts for replacement. Their service life is many times higher than their counterparts. In addition, they are covered by a warranty.

The main thing is not to forget that your actions can harm your smartphone. Therefore, if confidence is not enough, then it is still better to turn to professional craftsmen. Of course, you have to shell out money for this. But your nerves will be calm, and your smartphone will be reliable.

How to disassemble iPhone 6 at home

Disassembling an iPhone by yourself is the fastest and most reliable way to get rid of the warranty, but sometimes you have to go to extreme measures. I would like to note, just in case, that if a problem occurs, it is best to contact Apple technical support, where they will most likely help you.

If you feel competent enough and want to disassemble the iPhone 6 yourself, and are also ready to forget about warranty service, this article is for you.

You don’t need to have a lot of tools to disassemble an iPhone 6, here is a list of everything you need:

Screwdriver set Plastic spatula Tweezers Suction cup

I warn you, it is very dangerous to disassemble Apple devices. one wrong move, and you will end up with a brick worth several hundred dollars. You should not take on this business if you are not confident in your own abilities, as well as in the need for surgery.

  • 1. Disconnect iPhone 6.
  • 2. Remove the screws on either side of the Lightning port. There are a lot of screws of different sizes in the device, please mark them.
  • 3. Using a plastic spatula, gently pry the LCD display on several sides, then use a suction cup to gently detach it from the front panel. Do not damage the motherboard ribbon.
  • 4. Remove the 5 screws that secure the motherboard ribbon cable to the shield.
  • 5. Disconnect the motherboard ribbon cable from the screen using a plastic spatula.
  • 6. Remove the battery. On iPhone, it is glued to the back, but the glue is not too strong, so the battery can be easily removed.
  • 7. Remove the 2 screws that secure the metal cover of the battery connector and built-in speaker.
  • 8. Unscrew the 3 screws near the Home button.
  • 9. Lift the connector of the Home button and gently pull the Home button out.
  • 10. Remove the 2 screws that secure the metal cover of the main speaker and front camera.
  • 11. Eliminate the front camera and main speaker.
  • 12. Unscrew the 6 screws on the side panel.
  • 13. Lift the connectors and remove the SIM card slot.
  • 14. Unscrew the 2 screws that block the metal covering above the cable of the power button and volume buttons.
  • 15. Unscrew the 10 screws that secure the motherboard, pay attention to the hidden 2 screws under the black part at the top.
  • 16. Lift the ribbon connecting the power button to the motherboard.
  • 17. Unscrew the screw at the top of the device.
  • 18. Remove the motherboard
  • 19. Unscrew the 2 screws that secure the cover above the main camera, remove the camera.
  • 20. Unscrew the 3 screws that secure the internal speaker and remove it.
  • 21. Remove the 3 screws that secure the headphone jack.
  • 22. Remove the 4 screws that secure the Lightning port.
  • 23. Unscrew the 2 screws that secure the vibration motor and remove it.

To assemble the device, follow the same instructions in the opposite direction.

We disassemble the iPhone 4s

First, make a backup copy of your iPhone, because you may need to restore it after assembly. ITunes will help you make a copy. Be sure to remember the order of disassembling the parts of the device, or better, lay out the parts of the phone strictly in the order that was during disassembly and take pictures at each stage. Pay special attention to screws of different sizes. they should also be left in an order that is understandable for you, so as not to get confused during assembly.

  • First of all, remove the SIM card slot and the card itself from the device. To do this, you need an original paper clip from the iPhone set, but if you do not have one, a regular stationery will do.
  • There are screws on both sides of the charging connector. unscrew them.

The cover hiding the battery must be pushed up and disconnected. To the left of the battery, in the corner, there is a small protective plate that hides access to it. Unscrew these two screws too.

Now you can see the connector that fits the battery. It must be carefully removed. Remove the battery by pulling on the small plastic tab.

In the upper left corner you can see an S-shaped protective plate held by 5 round screws. Unscrew them.

The protective plate hides six loops underneath, they all need to be disconnected. Do not bend them or squeeze the cables too tightly.!

Five stubs are located on the surface and are completely visible, but the sixth is blocked and will be accessible after removing these five. Removing the leftmost ribbon cable allows you to remove the phone camera. At the same stage of disassembly, you will have access to the screw in the upper right corner, unscrew it.

When you remove the phone camera, remove three more screws. Two of them are located one above the other, under the plastic tab (which we used to remove the battery), and the third to the left, away from them. If you connect these screws with imaginary lines, it turns out. ⅃.

Now you come to remove the battery cable, it is relatively large, but to remove it it will be enough to lift it up.

Below, on the right, is the next screw to be removed. It is located at the very edge of the phone case. Now proceed to disconnect the antenna loop on the left. Its type is different from the previous connectors, but it connects in a similar way. This cable must be lifted carefully. After that, the antenna and ringer unit at the bottom of the iPhone will detach without additional effort. This is a black, elongated piece.

  • Pulling the orange cable aside, you will see another screw.
  • Unscrew the two pairs of screws. The first pair is at the bottom. Here, one screw was under the orange cable, and the second is located just above, on the right.
  • A second pair of screws are located at the top of the iPhone case. The first is next to the camera slot, in the upper right corner of the slot. The second is on the same level with the first, 3 centimeters to the right.
  • Thus, we freed the motherboard of the device and can dismantle it. Motherboard. a single block with circuits runs through the entire body of the phone. There is a washer-shaped piece next to the orange ribbon and it will also need to be removed. Note that it is seated on double-sided tape, so it will take some force to detach. Do not overdo it!

    READ  Where are iPhone backups on computer

    The next step is to remove as many as 10 screws holding the iPhone 4S module. Four of them are located in the corners, and the rest are located along the right and left edges of the iPhone frame. Note that the 6 side screws have a different size and the back has washers.

  • After this operation, there are still some screws left, but at this stage it is not necessary to disconnect them.
  • We carry with a specially prepared instrument (a pick, a plastic spatula) along the screen so that it detaches.
  • To replace the display module with a touchscreen, the available description is sufficient.

    To replace the iPhone 4S Home button, slide the black latch to the right. If you want to remove the iPhone 4S Home button, slide the black latch to the right. It is located above the charging connector. By the way, you need to remove it too, for this you have to unscrew two round screws. It is now possible to remove the long orange train.

  • The remaining connectors, including the cable from the phone start button (located on top) and the volume buttons will be disconnected if you unscrew the last screws.
  • This video clearly shows how to completely disassemble the iPhone 4 and replace the screen.

    How to disassemble an iPhone at home

    If you are interested in the topic of iPhone repair at home, then you must remember that you do it at your own risk. Not only does your phone lose its warranty after being disassembled outside an Apple service center. you can accidentally damage or improperly mount one of the gadget’s assemblies. Finally, Apple devices are quite difficult to disassemble on your own, manufacturers assume that you will only service them in branded centers.

    If this warning did not scare you, and you are firmly sure that you want to learn how to disassemble an iPhone at home. let’s move on.

    In this text, we will look at how to disassemble iPhone 4s, 5, 6.

    We disassemble the iPhone 5

    To do this, you need to unscrew a couple of small screws on opposite sides of the connector for charging the device. Finding them is not difficult at all.

    Next, using a vacuum suction cup, take out the screen. You can also perform the operation with a small plastic spatula or a pick. In this case, it is necessary to hook the screen from below, and then raise it. When performing the action, you need to be as careful as possible so as not to split or scratch the display.

    Also, the iPhone 5 often has a problem with easily erased paint. When disassembling the phone, you need to remember this at every stage of work.

  • After lifting the display, disconnect it from the main circuit block. the motherboard. Please note that the components of the device are quite tightly connected.
  • After unscrewing the last bolt on the board, carefully lift the screen cable. Here again you will need a pick or a plastic spatula. The screen can now be completely removed.
  • Dismantle the battery
  • In no case skip this disassembly step, because further actions with a connected battery may result in electric shocks. This is not only dangerous for you, but also causes defects in other parts of the phone.
  • The first step is to unscrew the three screws holding the protection on the battery cable
  • Use the same plastic spatula to remove the battery. The battery may not succumb to you the first time, but you shouldn’t worry about it. Gently pry it from different sides until the adhesive holding the battery comes off.

  • We take out and disassemble the motherboard of the iPhone 5
  • After removing the battery, unscrew the bolts that hold the camera. There are two of them. After that, we sequentially disconnect the microphone, speaker and headphone connectors. This is followed by the screws to which the antenna cable and SIM card slot are attached.
  • When you unscrew these 5 screws and disconnect the cables, slowly remove the motherboard.

    At this stage of disassembling the device, the iPhone 5 case can be postponed, because further manipulations take place directly with the motherboard. We remove the camera by unscrewing two screws. This unit does not have any additional fasteners and then freely detaches.

    We pass to the vibration motor, attached to three screws. Then, to remove the lower motherboard cable. To completely remove the bottom cable on the motherboard, which holds the Lightning port, headset jack, speaker, Wi-Fi antenna and one of the microphones, you need to unscrew seven more screws: two at the bottom next to the headphone jack, one in the right side of the loop and four more, directly holding the entire component.

  • Removing the CPU
  • To separate the iPhone 5 processor, you first need to remove the protective film from it.
  • Removing the details from the front panel.
  • When you have removed the remaining elements from the back of the machine, you can go to the front.
  • The “home” button is held on the glue, the button must be gently pryed off with a spatula and removed
  • One of the last pieces to be detached is a metal plate that protects the screen from touching other hardware parts of the device. After the last part is removed, the iPhone 5 disassembly can be considered complete.
  • In this video, you will learn more clearly how to disassemble the iPhone 5

    IPhone 6 disassembly

    Good news: iPhone 6 is easier to assemble and disassemble than its predecessors. This is undoubtedly due to the fact that the device has become thinner, but larger. Thanks to these changes, parts are easier to access and are housed in a more spacious enclosure.

      The screen of this device is held by two screws of the “pentalobe” type; to unscrew them, you will need a special screwdriver, about which we will say a few more words.

    Removing the display carefully with a suction cup.

    How to disassemble �� �� Apple IPhone 6S A1633, A1688, A1700 Take apart, Tutorial

    Using a suitable PH screwdriver, unscrew the metal protection blocking access to the loops. Until we remove it, we will not be able to pull out the screen. It is necessary to disconnect the metal plate that presses the cables and prevents the screen from being removed completely.

    The camera and the earpiece are placed on one cable, we disconnect them.

    We disassemble the display, it is necessary to remove the protective plate from it.

    The battery, as on previous models, is held in place thanks to double-sided adhesive tape. Use a plastic spatula to pry it from all sides until you can remove it. But be careful and careful.

    We take out the rear camera with tweezers

    After that, you should go to the polyphonic speaker.

    The charging connector on the iPhone 6 is located together with the audio connector, on the same cable, so they cannot be replaced individually.

  • Using tweezers, we separate the cable of the phone on / off button, volume and mute.
  • You can watch a more detailed disassembly of the iPhone 6 in this video.

    I would like to add a few words about the special tools that will be required to disassemble Apple smartphones.

    As we have already found out, we cannot do without:

    • Sucker
    • Plastic pick or special spatula
    • Tweezers
    • Special screwdriver set

    It is on screwdrivers that I want to dwell in more detail, let’s look at what characteristics and design they must have in order for iPhone disassembly to go smoothly.

    As an example of the optimal set of screwdrivers for electronics repair, we suggest considering a set of bits for precision work with a holder, manufactured by VIRA.

    First of all, the holder. It is made of impact-resistant plastic and has a rubber coating for easy grip. The holder is 11 cm long and can be wrapped in the palm of your hand without being too long.

    Traditionally, for such holders, it is considered important to have a rotating platform. You can push down on the tool and the body can be easily rotated with your fingers.

    • 25 mm SL1.5,
    • SL2.0, SL3.0
    • PH000 , PH00 , PH0 , PH1
    • T4, T5, T6, T7, T8, T10, T15, T20
    • H2.0, H4.0
    • PZ1 , PZ0
    • 0.8, 1.2, 1.5, 2.0
    • ▲, 2.0, 2.3
    • Y 2.0mm, ∪2.6mm
    • ⊙1.0

    The listed types of bits easily allow you to repair any unit of Apple devices, including the “pentalobe” slot.

    Particular attention should be paid to the material of the bits and their additional processing. The material is used with a high hardness so that the nibs will not wear off over time, or wear less.

    VIRA bits are made of chrome vanadium, a hard and durable material.

    Since iPhone disassembly is a constant work of small parts and small hardware, it is best to have the bits with a magnetic tip. So it is easier to pick up the fasteners, place them in the hole in the smartphone case.

    Particular attention is paid to the placement of the kit in the package. Each bit is in its own cell, they are fixed immovably and do not mix when carrying the kit. The box of the kit is made of high quality hard plastic that can withstand a drop to the floor from a height of human height.

    For additional storage convenience, the box has a retractable hook at the back. Thanks to this, the kit can be hung on the wall.

    How to independently reflash any iPhone at home

    Why did you suddenly decide to reflash your iPhone 5s, iPhone 4s, iPhone 6, iPhone 5, iPhone 4, iPhone 7, iPhone 6s, iPhone se, iPhone 3gs or another, now is not the time to find out.

    There are many reasons: your iPhone may be locked, found, and so on. The main thing here is STIHL and the right approach. so I will describe everything step by step.

    From the first lines, I also want to reassure you, if something goes wrong, for example, the files are unpacked, and the installation will not work, do not panic.

    You just have to go to the service, where this process will be completed with the help of more advanced tools.

    Re-flashing in the service is not expensive. depending on the region, it fluctuates between 5-10.

    The main purpose of this post is how to reflash an American iPhone, although I think I’ll write about a Chinese device too.

    Step one. completely reflash any iPhone yourself at home

    To flash any iPhone you definitely need the firmware you want to install.

    Where to get it. Below there are two sites where you can download any official firmware, just be sure to find out the exact name of your iPhone and select the appropriate firmware.

    • https://www.Apple-iPhone.ru/forum/viewtopic.php?t=5135
    • https://w3bsit3-dns.com/forum/index.php?showtopic=164173

    By the way, if you, for example, have an iPhone 5, then there are several firmwares for it. I recommend choosing the latest 10.3.3 right away and paying special attention to modifications to GSM and CDMA (if, for example, a phone with a CDMA connection, then GSM will not be installed).

    Install iPhone 5 or iPhone 5s with iOS 11, don’t even try. it won’t pull it because of the processor installed in it.

    Step three. reflash the iPhone yourself

    ATTENTION: be sure to charge the battery to 100%, otherwise you can be very sorry (if the battery cannot withstand you will have to open the device).

    READ  How to create an ID on iPhone 6

    NOTE: Before flashing, be sure to turn off Find My iPhone.

    Now, for flashing, you need to enter Recovery Mode or DFU on the iPhone. One won’t work use the second.

    To use Recovery Mode, turn off the iPhone completely, then connect it with a cable to a computer or laptop while holding the Home button.

    Now launch iTunes and wait for iTunes to find the iPhone. If the “Restore” window appears, click “OK”.

    If the message does not appear, select “Restore iPhone” while holding down the Shift key.

    A window will appear in which you need to specify where the firmware is located. We indicate the firmware file that you should have already downloaded, and I recommended that you put it on your desktop. Select and click “Open”.

    This stops your intervention. iTunes will do everything itself. At the final stage, we disconnect the cable and turn on the iPhone as usual.

    I hope the flashing was successful, and if not, it’s certainly sad, but there is another option. through DFU.

    Step two. reflash the iPhone yourself via a computer, via iTunes

    As you have already noticed, you need a computer (laptop) and a cable to connect the PC to the iPhone. I think you have it.

    Then if not yet, download the iTunes program from here, install and connect the computer to the phone, but do not turn it on, unless you want to make a copy, which will never hurt to recover from a flashing failure.

    It is advisable to place the downloaded iOS on the computer desktop so as not to search for a long time, although this does not affect the process itself, wherever it is.

    We have completed the initial stage, we move on to the second. set up the iPhone for flashing.

    Since I have already mentioned the iPhone 5 above, I will use it as an example, but on other devices such as iPhone 4, iPhone 4s, iPhone 5s, iPhone 6, iPhone 7 and so on, everything happens the same way, except for entering DFU mode.

    Step four. reflash the iPhone yourself via dfu

    To do this, first connect your device to your computer. The second is to turn off the device.

    Hold the power button for 3 seconds, then press the Home button without releasing the power button for 10 seconds.

    Release the power button, but continue to hold the Home button until iTunes informs you that it has detected a device in recovery mode.

    Further actions, as when flashing through Recovery Mode.

    NOTE: There is no home button on the iPhone 7. Therefore, after connecting, press and hold the “Power” button and without releasing it, hold down “Volume Down” and hold both buttons for 10 seconds. If the logo appears (picture below), then the buttons were held for too long. repeat the process.

    If the display stays black and iTunes displays a message stating that a device has been found in recovery mode, then you’ve put your iPhone in DFU mode.

    Use this method if the flashing through Recovery Mode for some reason did not work.

    Using a screwdriver, unscrew the iron plate that holds the front panel of the device:

    For this procedure, a small conventional screwdriver from any high-quality set of tools can be used. Here the screws of the Philips office are used, which, unlike the external Pentaloble, do not have a unique design.

    Remove the device motherboard:

    During this procedure, you should be careful not to destroy the motherboard and other components of the device.

    Remove the battery using a pick or other sharp plastic object:

    For this procedure, any sharp plastic object can be used that will not damage the components of the device.

    Disconnect the display cable using a pick or other sharp plastic object:

    For this procedure, any sharp plastic object can be used that will not damage the components of the device.

    Open the device using a suction cup or special tape:

    For this procedure, a special iSlack suction cup or the most ordinary double-sided tape that does not leave marks can be used. Since during disassembly at home there is a great opportunity to drop the phone, it is better to hold the device over a soft surface.

    We disassemble the iPhone 4s

    First, make a backup copy of your iPhone, because you may need to restore it after assembly. ITunes will help you make a copy. Be sure to remember the order of disassembling the parts of the device, or better, lay out the parts of the phone strictly in the order that was during disassembly and take pictures at each stage. Pay special attention to screws of different sizes. they should also be left in an order that is understandable for you, so as not to get confused during assembly.

    • First of all, remove the SIM card slot and the card itself from the device. To do this, you need an original paper clip from the iPhone set, but if you do not have one, a regular stationery will do.
    • There are screws on both sides of the charging connector. unscrew them.

    The cover hiding the battery must be pushed up and disconnected. To the left of the battery, in the corner, there is a small protective plate that hides access to it. Unscrew these two screws too.

    Now you can see the connector that fits the battery. It must be carefully removed. Remove the battery by pulling on the small plastic tab.

    In the upper left corner you can see an S-shaped protective plate held by 5 round screws. Unscrew them.

    The protective plate hides six loops underneath, they all need to be disconnected. Do not bend them or squeeze the cables too tightly.!

    Five stubs are located on the surface and are completely visible, but the sixth is blocked and will be accessible after removing these five. Removing the leftmost ribbon cable allows you to remove the phone camera. At the same stage of disassembly, you will have access to the screw in the upper right corner, unscrew it.

    When you remove the phone camera, remove three more screws. Two of them are located one above the other, under the plastic tab (which we used to remove the battery), and the third to the left, away from them. If you connect these screws with imaginary lines, it turns out. ⅃.

    Now you come to remove the battery cable, it is relatively large, but to remove it it will be enough to lift it up.

    Below, on the right, is the next screw to be removed. It is located at the very edge of the phone case. Now proceed to disconnect the antenna loop on the left. Its type is different from the previous connectors, but it connects in a similar way. This cable must be lifted carefully. After that, the antenna and ringer unit at the bottom of the iPhone will detach without additional effort. This is a black, elongated piece.

  • Pulling the orange cable aside, you will see another screw.
  • Unscrew the two pairs of screws. The first pair is at the bottom. Here, one screw was under the orange cable, and the second is located just above, on the right.
  • A second pair of screws are located at the top of the iPhone case. The first is next to the camera slot, in the upper right corner of the slot. The second is on the same level with the first, 3 centimeters to the right.
  • Thus, we freed the motherboard of the device and can dismantle it. Motherboard. a single block with circuits runs through the entire body of the phone. There is a washer-shaped piece next to the orange ribbon and it will also need to be removed. Note that it is seated on double-sided tape, so it will take some force to detach. Do not overdo it!

    The next step is to remove as many as 10 screws holding the iPhone 4S module. Four of them are located in the corners, and the rest are located along the right and left edges of the iPhone frame. Note that the 6 side screws have a different size and the back has washers.

  • After this operation, there are still some screws left, but at this stage it is not necessary to disconnect them.
  • We carry with a specially prepared instrument (a pick, a plastic spatula) along the screen so that it detaches.
  • To replace the display module with a touchscreen, the available description is sufficient.

    To replace the iPhone 4S Home button, slide the black latch to the right. If you want to remove the iPhone 4S Home button, slide the black latch to the right. It is located above the charging connector. By the way, you need to remove it too, for this you have to unscrew two round screws. It is now possible to remove the long orange train.

    The remaining connectors, including the cable from the phone start button (located on top) and the volume buttons will be disconnected if you unscrew the last screws.

    This video clearly shows how to completely disassemble the iPhone 4 and replace the screen.

    How to disassemble an iPhone without a special screwdriver

    How to unscrew screws from an iPhone case if you don’t have a special screwdriver.

    How to Unscrew iPhone Bolts At Home. INTEREST

    How to unscrew the sprocket bolt if there is no special screwdriver

    How do I open my phone? DIY screwdriver for all phones

    How to open the lid of the Chinese iPhone 5s and iPhone (NO TOOLS)

    How to remove any screw. BEST life hacks.

    HOW TO REMOVE THE LOOSE SCREW (Secret Information)

    How to disassemble iPhone 5s. How to open iPhone 5s.

    If you are interested in the topic of iPhone repair at home, then you must remember that you do it at your own risk. Not only does your phone lose its warranty after being disassembled outside an Apple service center. you can accidentally damage or improperly mount one of the gadget’s assemblies. Finally, Apple devices are quite difficult to disassemble on your own, manufacturers assume that you will only service them in branded centers.

    If this warning did not scare you, and you are firmly sure that you want to learn how to disassemble an iPhone at home. let’s move on.

    In this text, we will look at how to disassemble iPhone 4s, 5, 6.

    We disassemble the iPhone 5

    To do this, you need to unscrew a couple of small screws on opposite sides of the connector for charging the device. Finding them is not difficult at all.

    Next, using a vacuum suction cup, take out the screen. You can also perform the operation with a small plastic spatula or a pick. In this case, it is necessary to hook the screen from below, and then raise it. When performing the action, you need to be as careful as possible so as not to split or scratch the display.

    Also, the iPhone 5 often has a problem with easily erased paint. When disassembling the phone, you need to remember this at every stage of work.

  • After lifting the display, disconnect it from the main circuit block. the motherboard. Please note that the components of the device are quite tightly connected.
  • After unscrewing the last bolt on the board, carefully lift the screen cable. Here again you will need a pick or a plastic spatula. The screen can now be completely removed.
  • READ  How to remove a SIM card from an iPhone

    iPhone 6 Complete Disassembly

  • Dismantle the battery
  • In no case skip this disassembly step, because further actions with a connected battery may result in electric shocks. This is not only dangerous for you, but also causes defects in other parts of the phone.
  • The first step is to unscrew the three screws holding the protection on the battery cable
  • Use the same plastic spatula to remove the battery. The battery may not succumb to you the first time, but you shouldn’t worry about it. Gently pry it from different sides until the adhesive holding the battery comes off.

  • We take out and disassemble the motherboard of the iPhone 5
  • After removing the battery, unscrew the bolts that hold the camera. There are two of them. After that, we sequentially disconnect the microphone, speaker and headphone connectors. This is followed by the screws to which the antenna cable and SIM card slot are attached.
  • When you unscrew these 5 screws and disconnect the cables, slowly remove the motherboard.

    At this stage of disassembling the device, the iPhone 5 case can be postponed, because further manipulations take place directly with the motherboard. We remove the camera by unscrewing two screws. This unit does not have any additional fasteners and then freely detaches.

    We pass to the vibration motor, attached to three screws. Then, to remove the lower motherboard cable. To completely remove the bottom cable on the motherboard, which holds the Lightning port, headset jack, speaker, Wi-Fi antenna and one of the microphones, you need to unscrew seven more screws: two at the bottom next to the headphone jack, one in the right side of the loop and four more, directly holding the entire component.

  • Removing the CPU
  • To separate the iPhone 5 processor, you first need to remove the protective film from it.
  • Removing the details from the front panel.
  • When you have removed the remaining elements from the back of the machine, you can go to the front.
  • The “home” button is held on the glue, the button must be gently pryed off with a spatula and removed
  • One of the last pieces to be detached is a metal plate that protects the screen from touching other hardware parts of the device. After the last part is removed, the iPhone 5 disassembly can be considered complete.

    In this video, you will learn more clearly how to disassemble the iPhone 5

    IPhone 6 disassembly

    Good news: iPhone 6 is easier to assemble and disassemble than its predecessors. This is undoubtedly due to the fact that the device has become thinner, but larger. Thanks to these changes, parts are easier to access and are housed in a more spacious enclosure.

      The screen of this device is held by two screws of the “pentalobe” type; to unscrew them, you will need a special screwdriver, about which we will say a few more words.

    Removing the display carefully with a suction cup.

    iPhone 6 Complete Teardown Video

    Using a suitable PH screwdriver, unscrew the metal protection blocking access to the loops. Until we remove it, we will not be able to pull out the screen. It is necessary to disconnect the metal plate that presses the cables and prevents the screen from being removed completely.

    The camera and the earpiece are placed on one cable, we disconnect them.

    We disassemble the display, it is necessary to remove the protective plate from it.

    The battery, as on previous models, is held in place thanks to double-sided adhesive tape. Use a plastic spatula to pry it from all sides until you can remove it. But be careful and careful.

    We take out the rear camera with tweezers

    After that, you should go to the polyphonic speaker.

    The charging connector on the iPhone 6 is located together with the audio connector, on the same cable, so they cannot be replaced individually.

    Using tweezers, we separate the cable of the phone on / off button, volume and mute.

    You can watch a more detailed disassembly of the iPhone 6 in this video.

    I would like to add a few words about the special tools that will be required to disassemble Apple smartphones.

    As we have already found out, we cannot do without:

    • Sucker
    • Plastic pick or special spatula
    • Tweezers
    • Special screwdriver set

    It is on screwdrivers that I want to dwell in more detail, let’s look at what characteristics and design they must have in order for iPhone disassembly to go smoothly.

    As an example of the optimal set of screwdrivers for electronics repair, we suggest considering a set of bits for precision work with a holder, manufactured by VIRA.

    First of all, the holder. It is made of impact-resistant plastic and has a rubber coating for easy grip. The holder is 11 cm long and can be wrapped in the palm of your hand without being too long.

    Traditionally, for such holders, it is considered important to have a rotating platform. You can push down on the tool and the body can be easily rotated with your fingers.

    • 25 mm SL1.5,
    • SL2.0, SL3.0
    • PH000 , PH00 , PH0 , PH1
    • T4, T5, T6, T7, T8, T10, T15, T20
    • H2.0, H4.0
    • PZ1 , PZ0
    • 0.8, 1.2, 1.5, 2.0
    • ▲, 2.0, 2.3
    • Y 2.0mm, ∪2.6mm
    • ⊙1.0

    The listed types of bits easily allow you to repair any unit of Apple devices, including the “pentalobe” slot.

    Particular attention should be paid to the material of the bits and their additional processing. The material is used with a high hardness so that the nibs will not wear off over time, or wear less.

    VIRA bits are made of chrome vanadium, a hard and durable material.

    Since iPhone disassembly is a constant work of small parts and small hardware, it is best to have the bits with a magnetic tip. So it is easier to pick up the fasteners, place them in the hole in the smartphone case.

    Particular attention is paid to the placement of the kit in the package. Each bit is in its own cell, they are fixed immovably and do not mix when carrying the kit. The box of the kit is made of high quality hard plastic that can withstand a drop to the floor from a height of human height.

    For additional storage convenience, the box has a retractable hook at the back. Thanks to this, the kit can be hung on the wall.

    The iPhone is considered a rather complicated technique, but compared to other devices, it is easy to disassemble. This is good for the maintainability of the phone. After all, even an unskilled person is able to perform any manipulations with his gadget. True, this requires a set of special tools. But what if they are not at hand?

    All the insides of the iPhone open when you unscrew the two screws located on the bottom of the device. With a special screwdriver, this action will take at most a minute of your time. But with a little bit of smartness and a little more time, you can do everything without a tool. although the bolts have tiny threads, they are placed on the surface. Therefore, for untwisting, you can use a knife with a thin and sharp end. Other sharp objects such as needles, scissors and an awl are also used. Some go further and use women’s jewelry. Especially inventive people make absolutely wonderful objects. with the help of electrical tape and glue, they make the tip of a needle something like a screwdriver, but not everyone can afford it.

    However, nothing is better than a knife, which has been proven by personal experience.

    Drowned iPhone 5s

    What if I dropped my iPhone in water? For iPhone 5s owners, this situation can be a problem. The thing is that, according to the declared characteristics, these models are moisture resistant. The problem is that in fact 5s does not meet the given standards.

    For this reason, if the user suddenly drowned the phone of model 5, it is recommended to immediately carry out the initial drying, and then contact the service.

    Which iPhones are moisture resistant

    Increased moisture resistance and dustproofness are the slogans that manufacturers apply to iPhone 7 and above models. It’s all about modern IP67 technology. In part, such statements are true, but not 100% true.

    In fact, no iPhone device, even the most modern one, is able to completely ignore getting wet. Models from seven and above are close to ideal, but still sometimes fail. Very often, even after briefly getting wet, users encounter non-working speakers or dimming of the screen.

    What to do if iPhone falls into water. how to rescue your device

    If the phone falls into water, that’s at least a problem. But if the liquid got into the iPhone, then it’s just right to sound the alarm. The situation is often aggravated by incorrect and often harmful actions on the part of the owners of expensive equipment. That is why it is worth figuring out what to do if you suddenly drown your iPhone.

    What to do if iPhone falls into water

    What to do if iPhone falls into water? Unfortunately, this question is not uncommon among Apple users. Independent actions in this case can lead to big problems, so it is best to contact the service center as soon as possible.

    Simple tips that everyone should know will help save the phone from further problems. If the user drops the iPhone in water, then the first thing to do is:

    • Turn off the device and remove it from the case.
    • No need to shake your cell phone. It is enough just to turn it over with the ports down and wait until most of the liquid drains.
    • Remove all connected additional devices, such as a SIM card.
    • Dry the device with a napkin or cloth that absorbs moisture well.
    • Finally, it is recommended to carefully remove the back cover. To do this, you will have to disconnect the two end bolts. However, if such actions occur for the first time, it is best to refrain from them.
    • If you still manage to remove the back cover, you need to carefully dry the inside of the device. This is done using the same napkins or towels.

    Important! After first aid is provided, you will definitely need to contact the service. Only experienced specialists will be able to diagnose the device and identify possible problems at an early stage.

    Drowned iPhone ce

    Although this model came out much later, in fact these are the same sixes, only in a different case. As for the build quality and the degree of protection, everything is not so simple. According to manufacturers, se has high performance, but in fact, the quality is poor. Therefore, if the iPhone fell into water, the question of what to do implies only one answer: dry.