How to connect an antenna to your LG TV

Instructions: how to connect an antenna to a TV

To connect the antenna cable and the power supply, you must connect the cable to the plug in the power supply, where the antenna is active. The first step is to properly split the cable. To do this, you need to move one and a half centimeters from the end of the cable, and then carefully cut off the insulation. You need to do this in a circle.

When making cuts, it is important to take care not to damage the braid as well as the cable shield that is under the insulation.

After that, you need to move the screen hairs and foil back. It is necessary to step back from the braiding edge by 5 mm to cut the inner insulator and remove it. Then the cable is carefully wound under the plug so that the braid and screen touch the lower tinned pad.

connect, antenna

How to prepare the antenna cable:

  • Find the end of the cable.
  • Remove insulation.
  • Move screen.
  • Cut off the inner layer until the inner core appears.
  • Connect cable.

In order for the voltage to come from the antenna cable to the TV cable, it is necessary that the lower tinned plug pad is touched. The braiding of the central core must not be allowed to close. If a short occurs, the power supply indicator goes out or is dim.

Connecting a satellite dish to a TV without a receiver

Connecting a home TV to satellite TV is associated with a receiver. This is how it used to be possible to watch television channels. Today, you can make the connection yourself without using the receiver.

Many modern models are equipped with a built-in digital tuner and a special slot into which an access module is installed.

If the satellite dish is connected and configured correctly, the TV will receive the signal of the satellite operator, which will allow you to use satellite TV without connecting the receiver. For the correct connection, the satellite dish antenna cable must be connected to the connector, which is equipped with a special input. It is usually located near the input of the terrestrial antenna.

  • No need to buy additional devices;
  • The interior is not disturbed, so the receiver does not take up space.
  • Only one remote control can be used to view the channel.
  • The number of wires is significantly reduced.

To decode the channels, you will need to install a CAM module and an access card. Without the module, the viewing of television channels will be extremely limited. When the module is installed, the cable from the satellite dish should be connected to a special socket using F-connectors.

Steps for connecting an antenna to a TV

Before proceeding with the antenna connection, you need to take care of purchasing a high-quality television cable, at the ends of which the F-plugs should be fixed. If the antenna and TV cable are not properly connected, the TV signal will be lost, resulting in poor picture quality. The most crucial moment when connecting an antenna is choosing the right cable.

If a poor quality TV cable is used for the connection, even the most modern TV and properly attached plugs at the ends of the cable will not save the day.

To know which cable to choose, you must first study the issue of the movement of high-frequency current through the antenna cable. In an electrical network, current flows along the entire perimeter of the conductor cross-section. But the movement of the high-frequency current of the television signal is different.

Steps for installing the antenna plug on the cable:

  • You can make the connection yourself, since the voltage of the television signal does not pose a danger to human health.
  • When buying a plug for an antenna cable, you should pay attention to the fact that the standard size of the plug is suitable for a specific TV cable.
  • For screwing on the plug, the cable can be split using two methods: the braided shield can be wrapped or not wrapped. The first method is considered more reliable.
  • To split the TV cable, you need to cut the outer sheath of the cable inward. Do not press the knife too hard, otherwise the sheath may be damaged.
  • The incised shell is folded back and cut off where the cut begins.
  • The aluminum foil and copper braid are unscrewed. To give the foil strength, it is necessary to cover it with polyethylene from the inside.
  • Half of the unfolded foil is folded back so as not to degrade the quality of the contacts.
  • The central core is freed from insulation, and a plug is screwed onto the foil.
  • The central vein is “bite off” so as to leave from 2 to 3 mm.
READ  How to connect a phone to a TV via wi-fi

The other half of the plug must be screwed in until it stops, then both plugs will be ready for use. It so happens that after the plug is inserted, the TV cable interferes with placing the TV close to the wall. To avoid this, a plug with an angled design must be installed.

How to connect a TV antenna easy and simple

A home TV antenna is best organized with a splitter. A splitter is a metal box that includes one F-connector in and multiple connectors out. There can be several or many outputs: from 1 to 6. Depending on this, you can connect the antenna to several TVs at once.

To connect a home antenna correctly and efficiently, you must use a modern antenna cable with double shielding.

Double shielding eliminates a lot of electromagnetic interference. The central core of the cable can be completely copper, or it can be copper-plated. When choosing a cable, it is important to pay attention to the model of a particular TV.

How to connect an individual antenna:

  • Insert the cable into the TV socket.
  • You can use a splitter to connect multiple TVs.

For optimal connection of several devices, a splitter must be used. It will distribute the signal evenly. Such a connection is convenient when repairs are needed. If the TVs start to show poorly, it is necessary to check the operation of the signal network.

Instructions: how to connect an antenna to a TV

An outdoor or indoor antenna can be connected to the TV yourself. The voltage is safe for human life, so even a beginner can perform the installation. The signal quality will depend on the correct connection, and, consequently, the convenience when watching TV. The antenna is connected using a TV cable. His choice will depend on the TV model. The cable must be of high quality, otherwise the signal will not reach the TV, which will lead to frequent interference.

How to connect an antenna to your LG TV

The first question that arises when buying a new LG TV is how to connect the antenna and tune the TV channels? It is quite simple to do this on your own, without resorting to the services of specialists.

On the back of your TV there is a dedicated cable inlet for the antenna. Depending on the model, it may be marked with the abbreviation ANT IN. But even if there are no designations, it is impossible to confuse it with other inputs (for example, HDMI or USB), since it has a recognizable appearance, the same for TVs of all brands and models: it is a threaded cylinder with a hole in the center. The exception is very old TVs with cathode ray tubes (kinescopes), in which the coaxial connector looks like a flat cylinder with a smaller cylinder in the center.

Connecting the antenna to the TV Lg: step-by-step instruction

  • Make sure your LG TV is unplugged. This is necessary in order to avoid accidental damage to the TV or antenna during connection.
  • Locate the rear panel for the cable entry and connect the antenna. On some models it may be necessary to screw on the cable. To do this, rotate clockwise until the cable is securely fixed.
  • Turn on the TV to the network, after which you need to tune the channels.

After the antenna is connected to your LG TV, tune the channels.

If this is the first time you turn on your new LG TV, you will need to set the language and location before tune in the channels. These are important steps that you better not skip or postpone. over, it only takes a few minutes.

In order to set the language on your LG TV, you need to:

  • Using the remote control, press the “Settings” button.
  • Select the section “General”.
  • Use the joystick on the remote control to select the language you want.
  • Save changes made.

In order to set up a location on your LG TV, you need to:

  • Using the remote control, press the “Settings” button.
  • Select the menu item “Options”.
  • In the “Country” section, select your country of location.
  • Save changes made.

How to tune channels on your TV Lg: step by step instructions

The easiest and most convenient way to tune channels on your LG TV is to use the Auto Tuning feature available on all models. With its help, you can configure not only digital channels, but also analog.

If your LG TV supports the DVB-T2 standard, the European standard for terrestrial digital television of the second generation, then the satellite dish can be safely connected to the LNB connector without a receiver. In order for the TV to receive a signal, in the settings you only need to specify the correct signal source “Antenna” or “Satellite TV” (depending on the TV model). The vast majority of current LG TVs support this format. You can find more accurate information about your TV model in the “User’s Guide” or on LG official website. by entering the model number (a combination of numbers and letters) located on the back of the device.

You can also find the model and serial number on the TV itself. Using the remote control, press “Settings” / Smart (depending on the model), select the “Help” section, and in it. the item “Product Information”.

READ  How To Connect A Phone To A TV Lji

If your TV model does not support the digital standard, then in order to watch digital channels, you will need to additionally purchase a DVB-T2 set-top box and connect it to your LG TV.

How to activate Auto Channel Search on LG Smart TV:

  • Using the remote control, press the Settings button.
  • Select the menu item (Icon “Gear”) in the upper right corner of your TV screen.
  • Find the section “All settings”.
  • In it, select “Channels”, then click “Search for channels and settings”.
  • Click on “Autosearch”.

Important: To connect digital television, the DVB-T / T2 source must be indicated in the “Receive mode” column. For satellite or cable connections. appropriate sources.

  • Select the required source, click “Next”.
  • It will take a few minutes to find and tune channels. Do not turn off the TV in the process. When finished, click on the “Finish” or OK button (depending on the model).

How to tune channels on your TV Lg, not supporting function Smart TV: step-by-step instruction

Channel tuning on older LG TVs is slightly different, but also not difficult for the owner. Here’s what you need to do for this:

  • Using the remote control, press the Settings button.
  • In the settings menu displayed on the TV screen, enter the “Channels” section.
  • On the remote control, press the “Right” button, you will find yourself in the “Autosearch” item. Confirm the action by clicking OK.
  • Select the input source for program setting. It can be Antenna, Satellite or Cable TV. To tune digital channels, select “Antenna”.
  • Click the “Run” button on the screen.
  • It will take a few minutes to find and tune channels. Do not turn off the TV in the process. When finished, click on the “Finish” or OK button (depending on the model).

Problems that may arise when connecting an antenna to a TV Lg and channel setup:

What to do? Check if the antenna is connected correctly, if the signal source is correctly registered in the “Settings”.

  • No digital TV signal.

What to do? Change location in “Settings”.

What to do? Changing the frequency range and resolution of the TV screen may help. To do this, you need to change the screen format in “Settings” to “Original / Auto.” (depending on model) or Full Screen.

Required equipment for connection

Before installing an indoor antenna, the first thing to do is determine the location and distance to the nearest repeater, the presence of possible interference in the form of buildings, terrain features. The condition practically does not apply to the upper floors of high-rise buildings. Residents of the first three tiers may need a signal booster.

Some indoor antennas come with a built-in amplifier. Also, the device is purchased separately. The principle of operation is based on the amplification of the received signal. But the receiving device picks up both the direct signal and the reflected one from various obstacles. So, in a cluster of multi-storey buildings, the result will be rather negative. the reception quality will noticeably decrease.

The new models are equipped with a built-in DVB-T2 receiver, which provides reception of free Russian TV channels. For televisions of previous generations, you will need a receiver that provides support for the television standard used in the Russian Federation. Set-top boxes are widespread. from very simple models of a low price segment to complex, multifunctional devices.

The cost is influenced by the availability of additional functions. Internet connection, alternative control, HD support, CI encoding slot. These functions are essential for modern TVs. A functional tuner is not required when using a previous generation TV set. The only condition is support for DVB-T, DVB-T2 and DVB-C standards.

Samsung

Modern TV sets of the Samsung brand are equipped with a built-in DVB-S / S2 tuner. To connect a digital antenna to your Samsung TV, you need to follow the instructions.

  • Connect the antenna cable to the TV input, press start
  • Enter the TV menu, line “Broadcast” and select auto-tuning channels.

Next, set the type of source antenna.

  • In the line “Channel type” specify the full search mode and start scanning.
  • After the end of the search, all found TV channels will be saved automatically.

    In most LG TV models, in addition to the usual Ant In connector, there is a special LNB Satellite IN connector, which means that there is a built-in TV tuner. This output is designed to connect a satellite dish, to watch free channels with no coding. Tuning and searching for television channels or multiplexes is also performed through the menu, indicating the type of antenna. satellite.

    To connect an indoor antenna to an LG TV, they initially look at the type of connector, which can be:

    • RF. coaxial threaded cylinder with a hole in the center;
    • IEC standard, installed on older models.

    To search for signals correctly, after connecting, it is necessary to configure the user’s language panel and specify the search country in the “General options” tab. Then you can go to autosearch channels.

    • Select the “Settings” button on the remote control.
    • Then go to “Channels” and select autosearch.
    • Specify the type of input signal. antenna.
    • In the pop-up tab, click “Full”, then “OK”.
    • Activate the Run command.
    READ  How to connect wi-fi to a Samsung TV

    Connecting and configuring an indoor antenna

    The antenna is installed on the window sill and directed towards the repeater. You also need to make sure that there is no interference from radio signal sources. the Wi-Fi router should be located a few meters from the receiving device. Connect using a coaxial cable by inserting the wire connector into the dedicated jack. recommendations depend on whether the receiver has a built-in TV tuner or whether you are using a receiver.

    If you have a built-in DVB-T2 tuner, the antenna connection is as follows.

    • Find the connector on the rear panel marked with Ant In.
    • Turn off the device from the mains, insert the antenna plug into the socket, then plug it back into the mains. The action is due to the observance of safety measures.
    • In the “Channel settings” select the type of signal, activate the search.
    • Wait until the end of the search, save the found channels.

    In the future, sort the TV channels according to your preferences.

    In order to tune the home antenna on the TV when using a digital set-top box, the steps are performed in the following sequence:

    • Insert the antenna cable into the dedicated connector on the back of the TV tuner.
    • Connect the receiver using the supplied cords. HDMI or RCA cable.
    • After plugging into the network, select the input source. HDMI or RCA based on the type of connection.
    • In “Channel setup” start automatic search.
    • Save and sort TV channels.

    At the moment, Russian television has launched two basic free multiplexes. The third is planned to be released by the end of 2020. beginning of 2021.

    How to connect an indoor antenna to a TV: tuning algorithm

    An indoor antenna is considered a versatile and easily configurable device that is capable of receiving TV signals from the moment it is connected. But like any device, a TV antenna does not need a specific tuning algorithm. With this article, you will be able to properly connect an indoor antenna to your TV.

    Features of connecting to TVs of different brands

    The algorithm for connecting an indoor antenna to TVs of different brands is almost the same. But, each manufacturer has its own characteristics. These may be differences in the fastening of the connectors, the designations of the channel search settings. It is recommended to carefully study the user manual before connecting.

    How to connect multiple TVs to one antenna

    If, after installing the indoor antenna, the signal and image quality are excellent, then two or three TVs can be connected to it at the same time. It should be borne in mind that when using a passive device, the quality dividing into several devices deteriorates. Using an active antenna with an amplifier, provided there is no interference, the number of connected devices is unlimited.

    To connect several devices to one antenna, there are special splitters, splitters or so-called “crabs”, representing a rectangular box with loops. On one side of the splitter there is a connector marked IN. an input that provides an antenna cable connection, on the other there are several outputs marked OUT for connecting cables to receivers. In the absence of marking, there is always one input, several outputs in a row. Splitters come in 2 categories:

    The first option is connected to the mains, correctly separates the incoming signal. The second type is without a power supply. Consider the principle of connecting a passive splitter on the example of two connected TVs to one antenna.

    In addition to the splitter, you will need connectors. adapters, several plugs suitable for the jacks, a special coaxial cable. To connect two receivers, you need to buy a device with 2 outputs. If there are free outputs, 75 Ohm resistor plugs are required.

    The step-by-step connection algorithm is as follows.

    • Initially, the location of the splitter attachment to the wall is determined and the length of the cable is calculated: from the antenna to the splitter; from a splitter to two TVs.
    • Prepare the wires by winding F-connectors or connectors on them.
    • Lay the cable from the antenna, connect, fix the splitter on the wall.
    • Lay and fix coaxial wires from TVs, connect to a splitter.
    • Insert the antenna cables into the corresponding sockets on the TVs and turn on to check.

    If the image on two screens is clear and of high quality, then everything has been done correctly, nothing will interfere with watching TV programs. It is necessary to avoid places of accumulation of electrical, telephone and Internet wires. Foreign wires may interfere with signal transmission.

    Connecting and configuring an indoor antenna to a TV does not require specific skills or calling a TV technician at home. You must carefully follow the instructions, follow the rules of connection and settings. Enjoy watching.